Recent content by ??????

The HF Snap On copy Jack. The other low profile was OK, but I decided to get this for the 3 year warranty. Used it maybe 3 times is all, works good so far. It fits under my lower Camry and my sons Solara, so all is good.

I purchased the Daytona 3 Ton DS300LR, best specs all around. 2 issues, small saddle like 3 3/4 inches, and 90 day warranty. I got it home, it was a returned jack they sold me as new, had a paint spot on it the size of a thumbprint with a 1 dotted in the paint? Someone marking it maybe? or the...

FYI. I got my Sunex 6602LP floor jack, ordered from Home Depot for $236.32. All I had to do is take the top box cover off and knew it would be sent back. The lifting arm was way off center, maybe a 1/8 - 1/4 gap on the right looking form the rear of the jack. And about a 1 and 1/8 inch gap on...

Found this in Question section of the Sunex 6602LP from Summit: Sunex 6602LP - Sunex Tools 2 Ton Lowrider Service Jacks Is the saddle removable? If so, what size is the hole. I want to be able to use an EOM floor jack crossbeam with it that has a 1 1/4" stud. Saddle is removable with a 10mm...

Not sure. You would probably have to drill it and void warranty. I am ordering my Sunex 6602LP today, should be in by 4 to 10 days. I used up Home Depot gift cards as it was on sale for $236.32. I am going to explore that when I get it. I saw the AC Hydraulics saddle at Pelican, the one for the...

https://www.hcrcnow.com/shop/seal-kits/product/96664 https://www.hcrcnow.com/shop/seal-kits/product/4127 They are the same seal kit, Item number and price: 248949 $51.34

The AL2300 has a seal kit that can be purchased. Looks better than the average kit, but I do not have knowledge here.

I do realize that but it does not go back very far until you hit the rise. The ratings on HF are actually a little better for the DS300LR. I think the leaks are reported just a little more on that Super Duty in the reviews, many factors besides 1 U-cup seal. The best part of the Super Duty to me...

I just need some pics from someone that has a DK20HLQ to show me the height from the floor to the top of the saddle and then going down the length of the jack to see how fast it rises. If it worked for my Sienna, but not my Camry, I could drive the Camry up on 2 x 6's.

I would love the DK20HLQ, but I do not think it will slide under my 2013 Camry to the center jack point I use??

I looked them up a few days ago, and I was positive my 2003 Sienna was 6 and my 2013 Camry was 4, but I relooked and you are right, van is about 4 and the Camry is like 3300 or so. I agree a 2 ton will work. I mentioned the 2 ton Sunex/Arcan low profile, high rise jack. the one I am skeptical...

Could you take some pics and post them for me of the DK20HLQ? I can afford one but I am afraid the rise is too fast and it will not fit under the front end. My 2013 Camry may have 4.5 inches? i think my 2003 Toyota Sienna has about 6 inches? Like some pictures with a tape measure showing the...

That is not the right jack to compare to. The better one is the HF DS300LR, it is a low profile LONG REACH and is lower and goes further under the car before a rise. Not 3" though. It lists as 3 and one thirds inches. I am looking at the DS300LR and the Arcan Sunex ones listed in this thread. I...

Good points. I want an AC, but my requirements are not met. I need a low one and one that gets higher than 20 inches, the DK13HLQ meets those. But It is pushing it for my 6000 pound van so the 13 is out. The DK20HLQ would be perfect height wise and weight ratings, is low enough at the front...

Sure did, No Jumping, it is ALL about finding a good floor jack. Yes, I can read, hence my comment about frustration of the market.