Recent content by Cjcycles

  1. C

    Torque wrench tester

    I’ve used one of those little digital torque meters you connect like an extension. Checked a few of my torque wrenches on the snap on truck. Then compared with the little digital meter and got the exact same results. Your mileage may vary, but it’s a cheap solution to spot check them. Sent...
  2. C

    Looking for the most powerful cordless drill

    This is my recommendation based on your question. Sent from my iPhone using Tapatalk
  3. C

    Tool protective lubricant

    Lubriplate FMO350AW is the best thing I’ve ever used. Approved for food processing equipment so I assume it’s not as toxic as some others. I have an old master lock that I had oiled with WD 40 and would have to reapply ever couple months. I put one drop of Lubriplate in it about 8 years ago...
  4. C

    Food Grade Lubricating Oil?

    Lubriplate FMO-350AW Food grade, lubricant, rust preventive https://www.lubriplate.com/Products/Fluid/FMO-AW-Series/FMO-350-AW/FMO-350-AW/
  5. C

    Replacing old pressure washer:Recommendations

    This is hands down my favorite. https://www.mitm.com/pressure-washers/JP-1502-3ME1/98 This is a close second. https://www.mitm.com/pressure-washers/CM-1400-1MEH/378 Sent from my iPhone using Tapatalk
  6. C

    The Milwaukee addiction thread! :)

    The first one is a 2704 hammer drill and the second is a 2703 non hammer drill Sent from my iPhone using Tapatalk
  7. C

    2017 HD deals/sales/clearance thread

    Agree. It comes down to a bit of luck and hard work. I'm just not willing to commit 20-30 hours a week to visiting stores. I do stop by my local stores occasionally and look but it seems like deals are harder to find. I would attribute that to more people looking. This tread and slick deals...
  8. C

    2017 HD deals/sales/clearance thread

    Haven't posted here in a while. Most of the stores around here don't have anything of any interest marked down Sent from my iPhone using Tapatalk
  9. C

    2017 HD deals/sales/clearance thread

    I found a sweet glue gun on clearance Sent from my iPhone using Tapatalk
  10. C

    Pliers & Diagonal Cutters - Klein vs. Channellock

    Re: Pliers & Diagonal Cutters - Klein vs. Channellock Your welcome. The Irwins are readily available at Lowes. https://m.lowes.com/pd/IRWIN-8-in-Cutting-Plier/50289489 It might be worth looking into the NWS branded version, but it's nice to be able to pick the Irwin ones up at lowes...
  11. C

    Pliers & Diagonal Cutters - Klein vs. Channellock

    Re: Pliers & Diagonal Cutters - Klein vs. Channellock I'm sure there has been more comprehensive tests. This was just my experience. Your welcome. Sent from my iPhone using Tapatalk
  12. C

    Pliers & Diagonal Cutters - Klein vs. Channellock

    Pliers & Diagonal Cutters - Klein vs. Channellock I recently had to put together a tool kit for some of my technicians to complete a specific project. The project required cutting a small hardened stainless strap. I tested every cutter I could get my hands on. Cost wasn't an issue...
  13. C

    Pliers & Diagonal Cutters - Klein vs. Channellock

    I didn't realize I was going to piss people off recommending a set of irwin cutters. Sent from my iPhone using Tapatalk
  14. C

    Pliers & Diagonal Cutters - Klein vs. Channellock

    Irwin power slot diagonal cutters are hands down the best I've used. They are easy to pick up at lowes and are made in germany Sent from my iPhone using Tapatalk
  15. C

    2017 HD deals/sales/clearance thread

    If anyone in the Raleigh area wants a Milwaukee bottom box. I saw one in the over head at the store in Cary. Computer shows 0 but there is one in the overhead with a barcode. Sent from my iPhone using Tapatalk
See more
Top Bottom