Recent content by CloseEnough

  1. C

    Wanted: Snap-On FXWP8 extension.

    If you have this extension let me know how much you want for it, or what you may want to trade for it. Thanks! -Charlie
  2. C

    Track saw questions

    I have the Makita cordless and I'm obsessed with it.
  3. C

    WTT: my Snap-on short SAE combo wrench set for Metric stubbies

    I have this 1/4" to 1" set of Snap-on wrenches that I would like to trade for a metric set. I could really use a set of metric stubbies. These wrenches are in great condition. No markings. They were not abused in any way. Let me know what you got.
  4. C

    Porto or Snap-On 9mm Combination Wrench

    Looking for a 9mm combination wrench. Will buy from you or trade for something else (let me know what you need.) Thanks. Sent from my iPhone using Garage Journal
  5. C

    Mill head tramming, alignment

    Hell yeah! Good to go.
  6. C

    Show your adjustable wrenches!

    I like these. I have some of these in 8”. Sent from my iPhone using Garage Journal
  7. C

    1/2” Drive Shallow Metric Socket Set

    Preferably American-made. Let me know what you got. Thanks. -Charlie Sent from my iPhone using Garage Journal
  8. C

    Snap-on 12mm Impact socket (1/2” Drive)

    I’m looking for this socket to complete my set. I will buy it or I have lots of stuff to trade. Just tell me what you need. Thanks, -Charlie Sent from my iPhone using Garage Journal
  9. C

    Need Your Advice about a Questionable Torque Wrench

    It’s hard to say on those lower budget torque wrenches. Comparing it with the brand new Husky torque wrench is your best bet for an at-home calibration check. I doubt Powerbuilt will honor any sort of warranty on a 15 year old torque wrench. They are typically excluded from lifetime...
  10. C

    Got a Campbell Hausfeld Die Grinder model#TLO541...

    Sometimes they are just tight. Especially since it’s new. You might want to just take the nut completely off and see if if the bit will fit through just the nut and if it does try really pushing it in there. Maybe grind a little chamfer onto the bit and force it in there and hope that the...
  11. C

    Socket Warranty

    This is how I feel about pretty much every hand tool. If it breaks I just go buy a new one. If I break something its either because I was too hard on it and don't deserve a free replacement. If it wasn't from that then it's probably a piece of junk and I don't want another one. Haha!
  12. C

    FS: Complete & Incomplete Socket Sets & More! (Armstrong,Proto,SK & More)

    Re: FS: Complete & Incomplete Socket Sets & More! (Armstrong,Proto,SK & More) Chain Come-A-Longs JET 1/2 Ton Chain Come-a-long (JLH-50) $220.00 Shipped This is in new condition. This thing is very tiny. Usually when they are this small they are only rated for 1/4 Ton. This is rated for 1/2...
  13. C

    DeWalt 20v max batteries & charger

    NEW DeWalt 20v Max Batteries 2.0AH (DCB203-2) $70 Shipped NEW DeWalt 12v/20v Battery Charger (DCB115) $25 Shipped Buy them both together for $85 Shipped I've never shipped batteries before. It doesn't look too complicated, but I will need to ship them using the slower ground option. NOTE...
  14. C

    Torque Wrench necessity

    I'm an advocate for torquing everything. Especially on cars where the manufacturer provides you with a specific torque each fastener. There are many reasons why you would want to torque a fastener; -To make sure a bolt is enough -To make sure a bolt isn't too tight -To make sure a pattern of...
  15. C

    FS: Complete & Incomplete Socket Sets & More! (Armstrong,Proto,SK & More)

    Tool Clean Out I changed this thread to include different types of tools so that I'm not hijacking the classifieds with multiple posts of different tools. Thread #1: Sockets & Socket Sets. Updated 8-26-19 Thread #2: Come-a-longs. Updated 8-26-19 Socket Sets & More Armstrong Metric 12pt Deep...
Top Bottom