Recent content by I Love Grits

  1. I

    FS: 1994 Delta Unisaw with Unifence & Accessories - DFW, TX - $500

    SOLD: 1994 Delta Unisaw with Unifence & Accessories - DFW, TX - $500 Item has sold. Mods please delete.
  2. I

    Return to Glory --A Hotrod Shop-- (42x60 + lean-to)

    Thanks for the reply. First time I've seen it and I think its awesome. Have you reached any decisions on the internal layout? Now that the floors are done, I'd bet you have something in mind before moving tools back in. Also, not to be critical, but what are you hoping to gain with the two...
  3. I

    Return to Glory --A Hotrod Shop-- (42x60 + lean-to)

    Great looking shop! What were the deciding factors to go with LP Smart Side vs. drywall or similar?
  4. I

    Found a deal on craigslist? - List Here!

    Dallas, TX - Saylor Beall Compressor. $450 FIRM isn't a screaming deal given it looks like it's been used pretty hard. But for a single phase Saylor I would pick it up if I didn't already have one. It's been on there for about a week or so. Could probably get it for $400 if it stays much...
  5. I

    Found a deal on craigslist? - List Here!

    Dallas, TX - Champion Compressor 2 stage 5 HP $250 - Negotiable. Says to be in working condition. https://dallas.craigslist.org/mdf/tls/5394149345.html
  6. I

    Ford 4000 blast and paint. How O'Reillys matched the color.

    What type of setup do you spray with? Looks awesome.
  7. I

    Garbage Disposals

    Second this. Very nice to have it next to the faucet. Amazon has some off brands that are 30% cheaper or so than the Insinkerator name.
  8. I

    Garbage Disposals

    We have this one: http://www.amazon.com/Waste-King-L-8000-1-0-Horsepower-Continuous-Feed/dp/B000DZGN7Q/ref=zg_bs_3226848011_1/190-3488829-7733057 Quiet & powerful. Cheaper than Insinkerator too. I'd recommend it...
  9. I

    OK to terminate Plugmold Strip like this?

    Got the TR ones - really the only ones any stores around here carry anymore. I don't care for the TR plugs and how much force it takes to plug something in, but what you gonna do... Not sure when they started making them, but TR plug mold is all the brick and mortar stores around here carry...
  10. I

    OK to terminate Plugmold Strip like this?

    I share that same concern. Thanks for the input. Thanks for the feedback. That's what I'll do in order to avoid disturbing the IDC as mentioned by grounded-. These are going underneath an upper kitchen cabinet. I agree with you that the construction is less than impressive. But don't have...
  11. I

    OK to terminate Plugmold Strip like this?

    Yeah I wasn't sure if that was the appropriate word to use. You're assumption of what I was asking is correct. Thanks for the input! I feel better about it now.
  12. I

    OK to terminate Plugmold Strip like this?

    Hardwiring some plugmold strips underneath the cabinets in the kitchen. This is my first time working with them.There's not much room in the housing for much of anything. I'm using the pressure type connectors for the hookup. My question is: on the ends of the strip past the last outlet, rather...
  13. I

    Above 1200 Sq/FT 86's 20HP shop

    I might have missed it, but why the osb on bottom and drywall on top (vs all the same of one or the other)? Just curiosity. Keep up the good work getting cleaned up!
  14. I

    Free FastCap 11th Finger Push Stick

    Thanks signed up!
  15. I

    My new shop TV and DIY Ceiling mount

    Not OP but check out Monoprice. http://www.monoprice.com/Category?c_id=108&cp_id=10828
See more
Top Bottom