Recent content by inline five

  1. I

    Stuck Axle Nut Help, Possible to Snap Stud off CV Axle??

    I just measured my USA SK 36mm, it's around 36.2mm for comparison. But I doubt that is the issue. You just need more power, that Ryobi electric impact really doesn't have the nuts that the nicer impacts even at Harbor Freight. Something like this...
  2. I

    Is a 20 gallon compressor enough for air impacts?

    I have a Craftsman 25 gal 150 psi compressor and an older Harbor Freight Earthquake impact. I can fill the tank, and take all 20 lug nuts off my vehicle without having to run the tank again (it drops below its start up PSI, but there is enough left to remove all my lugs). I've done lots of...
  3. I

    DOWNSIZING: NOS and unused SK and Craftsman USA sockets, what price range?

    They're actually engraved and laser etched.
  4. I

    DOWNSIZING: NOS and unused SK and Craftsman USA sockets, what price range?

    Yeah the for sale stuff on eBay is always a joke especially the Cman stuff it seems. I agree I should look at "sold" listings however not any that I could find that were total complete sets like this. I wonder if I'll get a better hit if I just list them all as one sale for a specified amount...
  5. I

    DOWNSIZING: NOS and unused SK and Craftsman USA sockets, what price range?

    Thanks that helps a little. I know Cman USA can get crazy not looking to price high just want a fair amount.
  6. I

    DOWNSIZING: NOS and unused SK and Craftsman USA sockets, what price range?

    SK USA 1/2" | 6 Point | 10MM to 36MM (used the 30mm, that is the only one showing slight usage) Craftsman USA 1/4" 12 point | 3/16" - 9/16" Craftsman USA 1/4" 12 point deep | 3/16" - 9/16" Craftsman USA 3/8" 12 point | 1/4" - 1" Craftsman USA 3/8" 12 point deep | 3/8" - 1" Craftsman USA 1/2" 12...
  7. I

    Harbor Freight engine hoist

    IIRC there was some sort of issue with the silver ones. Some sort of design flaw. IIRC they were snapping on the boom and they reinforced the bracing. I highly recommend you buy a 2-ton however, as the reach is far greater than the one ton. I have the old orange 2-ton and it’s been useful...
  8. I

    Electrician Assistance Cost?

    $300 is a bargain for professional advice, just pay the man
  9. I

    Trying to figure out what breaker I should use for a welding circuit...GFCI or not

    $100? What is wrong with this one where you need to pay $200? https://www.amazon.com/dp/B001T5UYX8/?tag=atomicindus08-20
  10. I

    Where to go for questions on local code to install a few more outlets in garage (NC)?

    Thanks I just didn't know how to interpret the written code For an update, I might have a local guy willing to come out and help me do this the right way. I'm finding it very difficult to find a place that will even come out and advise if what I want to do is possible, and if not possible, what...
  11. I

    California Air Quiet Compressors Feedback?

    60 to 70 is a huge increase in noise level. Essentially, as far as your ear is concerned, it's basically double the sound level.
  12. I

    SK Tools

    Not for several decades after the switch.
  13. I

    SK Tools

    The chrome SK used is/was more durable. It went away here in the US with OSHA and EPA mandating (for good reason) requirements for reclamation (relevant to Erin Brockovich story) except for the higher end manufacturers (SO Williams etc, although they may have changed their chrome as well since)...
  14. I

    SK Tools

    I purchased some USA SK socket sets and wasn't impressed. Well, I was, with the chroming but the stamping was really inconsistent. SK had some sort of special chrome they used that was more durable and "blingy" than the standard stuff being used in the US. I have some Craftsman flare nut...
  15. I

    Anyone using battery adapters ?

    Then not relevant to the point you were inferring. You inferred 20v had more power than 18v, I think most assume you referred to lithium powered apples to apples.
See more
Top Bottom