Recent content by JustBob

You can get them here... http://www.gshields.com/items.asp?Bc=Morgan&Cc=Vises&Tp=&BrandName=Morgan&CatName=Vises+%26+Anvils http://robertstoolandsupply.com/manufacturer/milwaukee.html

Could not find one in 4 oz, but here is a 8 oz solvent can and caps. Only 2.9" wide, 1" depth, 5.4" high... http://www.freundcontainer.com/f-style-oblong-metal-cans/p/1900T01-B/

I talked to my local Quincy dealer, and according to the book they emailed me it is a 2000 model QT-7.5 AirMaster(not related to the current airmaster series). Although the book says it is pressure lubricated, I know it's not. I scoped the tank today, no rust in the bottom half but saw surface...

1) Is my current setup with the filter straight out of the tank stopping the oil from getting into my current hose? No, that filter is a coelescing filter and will only seperate aerosols or liquid water and oil. Oil and water vapors will pass through that filter. 2) Is my hose at this point...

I can't find my megger, but I did check the ohm's on the windings, the motor checked ok. The capacitors are fried and so is the starter. I will see about getting some more capcitors and trying to run it. Anyyone know of an online retailer for Quincy QT overhaul kits? Only one I could find was...

Oh, and why the hell does Krystal have a 8'6" clearence sign right there where you order, yet there is nothing else that you drive under? They now have a mangled clearance sign hanging by only one chain now... damn thing scratched my compressor!

I wish I could use 3 phase, but Im all set up for 240 single phase(actually 266 volts). I can get electric motors at cost so hopefully the 7.5 won't be to much. After thinking about it overnight I am leaning towards a total rebuild then fresh paint and decals. I had to make several stops on my...

I was getting ready to go to the hardware store and was checking my email before I left. Decided to check CL real quick and this is the first thing I saw when i opened the tools section... I called the guy immediately and he had just posted it! I just had to have it... went straight to...

That would be the unloader line, it is to relieve pressure between the tank and the pump when the compressor cycles off so that the pump and motor do not start under a load. You want to make sure and hook it back up so that it works properly, there will be a small amount of air escaping when the...

A compressed air water/oil seperator removes the water/oil form the air stream. A coalescing filter is a seperator. A coalescing filters main function is to remove water and oil aerosols by coalescing the aerosols into droplets. This happens partially because of torturous path and pressure...

I have the same unit and had to do 2 flushes in the last 3 months due to the first gear box replacement went bad. The easy and most thurough way to flush with this unit or a powered version of it, is to take both hoses off of the gear box. Place the hose from the flushing unit onto the power...

I just measured mine, 7/32 or 1/4 inch... all 3 sizes.

Holy ****... Mine is due tomorrow as well, I can not remember the last time I was this excited for a tool delivery! Alex, outstanding customer service, shipping, and communication with your customers!

I would like to thank Funky for bringing this to our attention, Bull for rallying the members and his passion for helping a small business owner, and Ironhorse and others for their reviews and pictures. I ordered two full sets, to replace the HF units that are in my box now, as I have been...

I have not found another tool, electric or otherwise, that will do the job a hand impact driver will. Indespensible when needed, mostly forgotten when not... I have two Lisle sets purchased, both from the early 80's, the tools themselves are great but the bits cant take much abuse. I will...