Recent content by k5fd89

  1. K

    Which leatherman are you using?

    Have three or four leathermans most are discountinue models but my main carry is a PSTII PSTII was a replacement from leatherman as I sent my original Leatherman in for repairs after 10+ years of use, but since it was a retired tool it was not repairable so a upgrade replacement was sent. I...
  2. K

    Done with jackstands

    Here's a link they are very close to carquest ramps. Not a lift but give extra room and are more secure http://www.autoramps.com/ultra_ramps.htm
  3. K

    What tools do you take to pull parts?

    sun block Water Electricians tool bag (local yard has wheel barrows and carts at gate usually grab one) 18v dewalt grinder (best yard tool there is) 18v hammer drill 18v sawzall 18v battieres 1/4 socket set 3/8 socket set Pry bar Claw hammer Multi bit screwdriver Various pliers Stars and...
  4. K

    Done with jackstands

    Try thesehttp://www.carquest.com/webapp/wcs/stores/servlet/product_Heat+Guns+%26+Accessories%2FRamps%2FCabinets+Heavy+Duty+Truck+Service+Ramps+-+Stamped+Steel+-+Total+Ramp+Size%3A+35+%22+long+x+13+%22+wide__10151_-1_10651_198608_36823?acesApp=0 I drive up front then jack up rear and put second...
  5. K

    Anybody Used Lizard Skin as Insulation in a Metal Garage

    Got the same garage just in a frame and have been thinking about doing this too. I am putting foam board on the ceiling but the side walls I have been looking at lizard skin as well. It works great in my car, but been really questioning if it would work in my barn. My one thought is if it does...
  6. K

    Tile cutting?

    Its dusty and loud and not the best but for just a few cuts it works great. Mines about five years old and has never let me down. http://www.harborfreight.com/power-tools/tile-saws/4-dry-tile-saw-68298.html
  7. K

    Dunlap Scroll saw

    This is a Dunlap scroll saw my grandfather purchased for his steel mill in the 50's (not sure of exact dates). He purchased about five of these and most have been take by family members but this one needs a home. It does work and the power cord was upgraded in the early 90's when it was last...
  8. K

    Source for Nerf/Step Bars - 2010 GMC Sierra Crew Cab

    Also check 4wheelparts for weather tech digital fit. Front mats should run around 100ish range and rears are around 75 dollar range. Might not be cheapest place to buy but unless you get free shipping online you will be ahead buying local.
  9. K

    Source for Nerf/Step Bars - 2010 GMC Sierra Crew Cab

    Haven't had any issues with support and as far as strength someone miss placed a tube behind a Tahoe and the Tahoe was driven over the tubes and not a scratch on the tubes. I been selling them since 09ish and have yet to have a set returned.
  10. K

    Source for Nerf/Step Bars - 2010 GMC Sierra Crew Cab

    I have sold and installed more them 50 of these and everyone has loved them not to mention they are cheap. There are really only two maufactures of these type steps. all that changes is the name on the black mat. 4wheel parts has alot of stores in texas so you could avoid shipping cost and...
  11. K

    How do you keep mice out of a stored car?

    Big dog that hates anything in her yard. If I could only teach her to throw them away instead of bringin them to me. [/IMG]
  12. K

    Dorman or Auto 7 replacement parts??

    Cross check and see if it's the same wiper motor for a KIA car. Most Hyundia and KIA parts are interchangeable and KIA is usually a lot cheaper.
  13. K

    Eagle carports new build

    I have a TNT 24x24 and a quality outdoors 16x36 and both are great. I will say the TNT is a more finished then the quality outdoors but both have done the job. The TNT has two roll ups and two windows, while the quality has just one roll up. The one roll up was huge mistake cuz it gets very hot...
Top Bottom