Recent content by Levaughn

Yep! At first I thought it was a light meter until I saw the name Minox. I opened it and it has film in it rolled to one side of the spool.

I picked up these items today at an Estate Sale for $20. - Minox B Miniature Camera - GE Clock Radio - Ciner Hinged Bangle Bracelet Gold Tone With Rhinestones - Sewing Needles - Miniature Knives

These are some items I picked up last Saturday at a Yard Sale for $15. - Allied Wire Strippers - Proto # 4993 Folding SAE Hex Key Set - Mattel Hot Wheels Slip Joint Pliers - Husky 17mm Ratchet Wrench - Joran 3/8 Cement Drill Bit - Battery Terminal Remover Tool - Nuova Faro Italy 12mm Open-End...

I picked up these items today at an Estate Sale for $25. Craftsman 9/16 - 5/8 Wrench Craftsman 9/16 - 1/2 Wrench Craftsman 5/8 - 3/4 Wrench Craftsman Torx Drivers Craftsman Hollow Set Screw Key Assortment Craftsman Pliers Proto # 5316 1/2 inch 1/2 drive 12 pt Socket P&C # 6024 3/4 inch 12pt...

These are some items I picked up yesterday at an Estate Sale for $25. Craftsman 1/2 Wrench Craftsman Vintage 25/32- 13/16 Wrench Craftsman Screw Driver Keuffel & Esser Ruler Wiss Snips None Better 5/8 3/8 Drive Socket None Better 11/16 3/8 Drive Socket Firepower P-10 Propane Torch No Name Tools...

I’m cleaning up my 1940s to mid-1950s Sears Homart fan I haven’t touched since purchasing it at a Yard Sale about fifteen years ago for about fifteen dollars. I took the screen off and noticed the motor is built by Packard Electric. GM purchased Packard Electric in 1932, and Packard Electric...

I changed the radiator fan on my 2011 Impala. On Sunday while driving on the highway an hour and a half each way, I hit a deep pothole. I thought nothing of it because the car drove fine. Later in the day after the trip, I noticed the temperature gauge which normally stays in the middle was...

I starts about at the 6:43 mark where he removes the O-Ring from the pump handle shaft. It's not the same pump but the same principle.

I bought the 20 ton press over fifteen years ago. About a month or two after purchase, it started leaking. I only used it a few times because I was disappointed. About two weeks ago I decided to watch a video on taking the pumps apart and rebuilding them. It turns out the pump handle O-Ring was...

I picked up this compression tester with these attachments yesterday at an estate sale. On the face of the tester is the word "bar" I was wondering if that's the manufacturer, but it's written in lower case letters. Thanks.

I picked these items up yesterday at an Estate Sale for $30. - Husky Hex Sockets - S2 Hex Sockets - Herbrand # H-11 3/4 Ratchet - Williams # H-1228 3/4 Socket - Compression Tester With Accessories - Pittsburgh Impact Extensions - Pittsburgh Hex Key Set - Pittsburgh Bearing Set - Craftsman 1/4...

I removed the old O Ring from the pump handle and replaced it with an O Ring I had from my plumbers pack. I bled and filled it. It's been about 24 hours and no leaking yet. I'll see.

It has to be about twelve years old. It started leaking a few months after I got it and used it maybe three times. I didn't want to be bothered with it, then I just read that all I had to do was take the cotter pins out the pump handle and there was a piston in there with O Rings. I thought I...

Thanks. I figured as much. I thought someone may have had to replace an O Ring and could recommend a replacement.

My Central Machinery 20 ton bottle jack leaks around the pump handle on my press. I see I can slide the piston out at the pump handle and replace the O Ring. Can anyone recommend replacement seal kit? Thanks.