Recent content by sqznby

  1. S

    Safe to install an angle grinder cut off wheel on a bench grinder?

    If you have an arbor to hold that thin of a blade on your bench grinder sure, and you let the tool do the work, I don't see a problem with it. If you do stupid things then stupid things will happen.
  2. S

    Teaching a New Welder - What Do You Wish You Had Been Shown?

    I like the idea of starting with Oxy-Ace. But in all honesty, she will more than likely never use it. Had to build a 4" box using Oxy-Ace for my first class. Had to build up and hold pressure to move on to the next stage of the class. I'd find out what she was interested in and where she...
  3. S

    Polishing out scratching

    Me thinking this was bare metal haha. I'm with shiftless
  4. S

    Polishing out scratching

    Sometimes you have to go back before you can move forward. Meaning go back to a course grit to clean up what you couldn't get out before. It could've been a deeper scratch that wasn't noticed until cleaned up. Go through the specific grits and after use a decent compound. And while a polisher...
  5. S

    Dynasty 400 vs Invertig 251

    If you don't mind me asking. Where about in NC are you or the machine located? If you're already set up with a mig, why not use that? Unless it calls for tig specifically, just curious.
  6. S

    Welding Helmet Recommendations

    Arc One Hawk is a solar only hood. I'd recommend this hood to anyone, experienced or hobby welder. It might not have all the bells and whistles, but it is the lightest hood out there. Can't remember what shade but it's an 11 or 12.
  7. S

    Angle Grinder PPE

    I'm probably going to get sh*t for this but I'm just being honest. What the f**k are you going to do with that suit? What are you doing to justify wearing that? What kind of work are you doing? Seriously? You went from black and decker cut off wheels to harbor freight cut off wheels when it was...
  8. S

    SOLD-Random Tools

    SOLD
  9. S

    Honda Generator Surging Under load only

    I have used torch tip cleaners in the past to clean some of the passages but never drilled any out. I use CRC Mass airflow cleaner to clean all of my carbs and 99 percent of the time I never even remove the carb. Pull the filter and the bowl and spray directly in every orifice of the carb and up...
  10. S

    Angle Grinder PPE

    Can't blame the tool or the bit, operator error is the end result. All the PPE in the world can't help someone using a tool incorrectly. Proper rotation should shoot the sparks down/at you and the rotation should pull the grinder away from you.
  11. S

    Fein/Slugger 14" blade

    Fein/Slugger 14" cold chop saw blade for cutting stainless $100 shipped to the lower 48 PayPal
  12. S

    Bernard BTB Q4 MIG Gun - 400 amp Q4015AE9EMC

    Bernard BTB 400Amp 15' Mig gun New never used, opened to take pictures. I have two. Pictured for reference but NOT INCLUDED are the tips that it uses. PP friends and family preferred to avoid any fees Shipping UPS Ground w/tracking
  13. S

    SOLD-Random Tools

    Going through some of my stuff and trying to thin the herd. Have a lot of doubles and triples and quadruples that I just don't need. 3- Mitutoyo Digital Protractors. They're new never used. SOLD 1- Utica TS-30 torque screwdriver. New never used SOLD 2- Mitutoyo Bevel Protractors. Used I'd...
  14. S

    Show us your welding projects

    That looks great, I really like that design nicely done.
  15. S

    grinding tig tungsten

    Nice, Looks like it's a keeper
Top Bottom