To avoid these ads, REGISTER NOW!

Above 1200 Sq/FT Chesnut Acres 1926 Dairy Barn (36x126)

Wokspaces above 1200 squarefeet.
OP
T

tj675

Well-known member
Joined
Apr 9, 2019
Messages
909
Location
The Mitten
The flagstone walkway looks great, however my back couldn’t handle another winter of shoveling it.

Pulled the old stones Monday, framed it up Tuesday, had a friend help with the pour on Wednesday, cut joints and pressure washed to expose the aggregate Thursday, clean up yesterday and today.
IMG_4014.jpeg
We had a really good base to work with and added mesh after this and rebar in the porch.

IMG_4017.jpeg

It’s nice not having to watch each of your steps.
 
To avoid these ads, REGISTER NOW!
OP
T

tj675

Well-known member
Joined
Apr 9, 2019
Messages
909
Location
The Mitten
SilverJimmy said:
How will the exposed aggregate hold up to winter snow and freeze/thaw cycles? The apron at our house in Prescott is failing pretty badly and needs to be replaced from winter weathering.
Click to expand...
We had really good luck with it at our last house. In addition to the pea gravel sized aggregate they must use some type of binder because cleaning the overspray off everything after exposing the aggregate took quite a bit of work with the pressure washer.
 
OP
T

tj675

Well-known member
Joined
Apr 9, 2019
Messages
909
Location
The Mitten
Mom asked that I make her a new TV cabinet last year and it finally made it to the top of the list. Started with some maple plywood and built a quick bottom case. The HD plywood is junk however I was too lazy to drive two hours to get a quality product.
IMG_4045.jpeg

Added some maple trim and drawer fronts.
IMG_4046.jpeg

Next up was the top surround.
IMG_4047.jpeg


Added some crown to the center and started on the side case.

IMG_4054.jpeg

She didn’t want “doors” or adjustable shelves so I just added some quick and dirty shelf supports. Still need to finish up the shelves for the side cabinets and some sanding.
IMG_4058.jpeg
 
OP
T

tj675

Well-known member
Joined
Apr 9, 2019
Messages
909
Location
The Mitten
jar944 said:
Nice TV cabinet.

If you go through through bunk you can usually find enough decent sheets to make it work.
Click to expand...
Don’t get me wrong I spent some time going through the bunk and the veneer was really nice.
My issues came when breaking the sheets down, the amount and size of the voids in the plywood was the problem. One panel had a 12” x 3” void in the center layer and another panel delaminated when I cut a dado. Two other panels developed bows when they were cut down to size and I can only think that must have been from voids as well. Ended up making it all work, but it wasn’t without a few cuss words.
 
J

jar944

Well-known member
Joined
Jul 26, 2010
Messages
6,030
Location
Northern VA
tj675 said:
Don’t get me wrong I spent some time going through the bunk and the veneer was really nice.
My issues came when breaking the sheets down, the amount and size of the voids in the plywood was the problem. One panel had a 12” x 3” void in the center layer and another panel delaminated when I cut a dado. Two other panels developed bows when they were cut down to size and I can only think that must have been from voids as well. Ended up making it all work, but it wasn’t without a few cuss words.
Click to expand...

Wow, that's pretty bad. I've had the occasional void and edge delamination but not to that extent. I wonder if the different plants have that much of a difference in quality. I was getting all the HD purebond from the west virginia plant (and it had a poplar core)
 
To avoid these ads, REGISTER NOW!
OP
T

tj675

Well-known member
Joined
Apr 9, 2019
Messages
909
Location
The Mitten
jar944 said:
Wow, that's pretty bad. I've had the occasional void and edge delamination but not to that extent. I wonder if the different plants have that much of a difference in quality. I was getting all the HD purebond from the west virginia plant (and it had a poplar core)
Click to expand...
This plywood was marked from Columbia in Canada.
These two pieces were from two different sheets, same bunk.
IMG_4060.jpeg

IMG_4061.jpeg
1/8” twist over 30”
IMG_4063.jpeg
 
Last edited:
OP
T

tj675

Well-known member
Joined
Apr 9, 2019
Messages
909
Location
The Mitten
I put this in the Woodworking forum and will add it here as well.

Looking for input and ideas for an a dedicated assembly table. I’ve been using my outfeed table however its length was restricting the assembly of bigger projects.

I have a nice hand tool workbench so this will be used for prep and assembly of projects.

Maximum size: 5’x 10’
Top material: Butcher block maple

Should I drill the top for bench dogs or use T track or skip it all together?

Would you add vise? If so what type?

I have a 4’x4’ 5/16” piece of stainless, that’s been leaning against the wall for 10 years, that I was thinking of inlaying in one corner of the top.

The legs are 16/4 mahogany and I am using 8/4 hard maple as the stretchers.
IMG_4084.jpeg
 
Last edited:
OP
T

tj675

Well-known member
Joined
Apr 9, 2019
Messages
909
Location
The Mitten
It’s been awhile. Since the last post I painted and delivered mom’s TV cabinet.
IMG_9716.jpeg
My sister wanted a table for behind her couch that she could put bar stools under. Made the legs to match the feet on her dining table from a few years back.
IMG_4146.jpeg
IMG_4156.jpeg
IMG_2946.jpeg

It has finally been long enough since our utilities ran natural gas down our road that we didn’t have to share the cost when hooking up. ($10,000 vs $200).
IMG_4168.jpeg
Wife wanted to paint her she shed so we did that as well.
IMG_4142.jpeg
How it looked before
IMG_4152.jpeg

Started working on the new assembly table.
IMG_4171.jpeg
 
OP
T

tj675

Well-known member
Joined
Apr 9, 2019
Messages
909
Location
The Mitten
Set the two 30” x 120” tops on the bench this morning. Will use the tracksaw to joint an edge on each before dominos and glue. I’m happy with the size and height. I can tell that I will need to put some floor leveler in what was the front foot hold next to the curb.

IMG_4173.jpeg
 
You must log in or register to reply here.
To avoid these ads, REGISTER NOW!
Top Bottom