Welding mild steel to hard mystery plate

[rslaback]

I've got a work project that involves welding some strips of A36 to a piece of hardish something on a large metal cart.

The cart was originally used to move around injecting molding tools. The top of the cart is a piece of 1/2" thick plate. I know the top is hard because when someone welded to it once before the welds cracked off easily when hit with a hammer. It also didn't like being cut by my carbide cold saw. But I also know it isn't the hardest steel in the world because it does have scratches on it and the plate is welded to mild steel legs (MIG from what I can tell).

I know my best shot is a preheat to around 800 and then a long cool down with torch reheats but I'm open to other tips as well.

I'm also stuck with MIG because of equipment on hand.

 

[larry4406]

I can’t offer welding help, but can the attachment be redesigned to a drill, tap, and bolted connection?

If hardened probably a PIA to drill and tap as well.

 

[PCustoms]

I've got a work project that involves welding some strips of A36 to a piece of hardish something on a large metal cart.

The cart was originally used to move around injecting molding tools. The top of the cart is a piece of 1/2" thick plate. I know the top is hard because when someone welded to it once before the welds cracked off easily when hit with a hammer. It also didn't like being cut by my carbide cold saw. But I also know it isn't the hardest steel in the world because it does have scratches on it and the plate is welded to mild steel legs (MIG from what I can tell).

I know my best shot is a preheat to around 800 and then a long cool down with torch reheats but I'm open to other tips as well.

I'm also stuck with MIG because of equipment on hand.

Is this a "must do" or just trying to modify an already modified dodad?

It's probably a chunk of tool steel, not sure what the process is for welding on it but I'm not sure I'd repurpose a stripper plate into a die cart...

 

[rsanter]

I would heat with a torch to at least a dull red and then hit with the mig welder while still red hot

 

[rslaback]

Is this a "must do" or just trying to modify an already modified dodad?

It's probably a chunk of tool steel, not sure what the process is for welding on it but I'm not sure I'd repurpose a stripper plate into a die cart...

It's kind of a salvage job. We needed to move a tool with a hydraulic cylinder mounted to the bottom so the cart got a hole torched in it. I'm trying to turn that mess into a more usable cart with a removable plate to allow both uses. The strips to hold the plate in place are what I'm hoping to weld.

 

[rslaback]

Everybody loves pictures right?




The original construction has the top welded on.



Scars from the previous coworker welds that snapped off easily.



The ledges that will get welded in to support the plate.

 

[whateg01]

I might try to find a piece of 11 ga bigger than the top and either fold the edges down or attach strips of angle or bar to the bottom to keep it from sliding off. Seems less hassle.

 

[RoninB4]

-I'm not a welder but there doesn't look like much depth of penetration on the weld from your co-worker. I would contend that this isn't what I'd call "tool steel" as it's too large for the expense of real tool steel. As for it being from a stripper plate...kinda large for that and stripper plates are usually just 4140 PH unless there's a special reason to use tool steel inserts. These are opinions based upon machine shop and die making experience. I'll leave more informed opinions for an actual welder to chime in.

 

[Steve from Socal]

That may be abrasion resistant steel not 'tool steel' Preheat to at least 500. Mig welding don't do short arc, use spray.

 

[rslaback]

That may be abrasion resistant steel not 'tool steel' Preheat to at least 500. Mig welding don't do short arc, use spray.

Would abrasion resistant steel tell the carbide blade in my cold saw to **** off? It did cut it but it did a number on the blade.

 

[Steve from Socal]

Yes

 

[RoninB4]

Would abrasion resistant steel tell the carbide blade in my cold saw to **** off?

-With a heat treated hardness of 500 BHN (50 Rc) for AR steel I wouldn't think carbide would have trouble cutting it unless your blade is dull.

It did cut it but it did a number on the blade.

-Were you cutting near a welded section? Welding can create crystallization in the metal that could cause trouble.

 

[Steve from Socal]

-With a heat treated hardness of 500 BHN (50 Rc) for AR steel I wouldn't think carbide would have trouble cutting it unless your blade is dull.

-Were you cutting near a welded section? Welding can create crystallization in the metal that could cause trouble.

AR will dull a carbide tool that is not fed with consistant moderate pressure,

 

[john.k]

Wearplate is most likely ......to weld ,use a 312 or 316 stainless rod .....the more preheat the better with HSLA steels

 

[MongoTA]

Run a file across the edge and see if the file cuts or if it skates across. If it skates, it could be hardened steel.

 

[john.k]

The weld breakout is known as a ''clip test'' ...you weld a clip one side .then break (or bend flat) it out with hammer blows .

 

[goldtang]

I am not a welder just worked with a few over the years from memory and at a guess if the plate is hard to work with it may be some form of wear/ abrasive resistant plate , you would will Have to heat it to about 150 Celsius/300 Fahrenheit the whole area to be welded and use low-hydrogen MIG wires Let it cool slowly , just my 2 cents ,

 

[VR6ix]

I'm also stuck with MIG because of equipment on hand.

How many amps are available? To weld 1/2" steel to 1/2" steel, you'll need a few...

Do the file test as stated above as well.

 

[cody1325]

Possibly something like Hardox?

 

[rslaback]

How many amps are available? To weld 1/2" steel to 1/2" steel, you'll need a few...

Do the file test as stated above as well.

250

 

[dffay]

There are Problem Solver Welding Electrodes that are a stick welder solution for joining mystery metals. All must be ferrous but wildly different tensile strengths and carbon content.

 

[john.k]

Generally 312 or 316 stainless .......austenitic deposit does not cause hydrogen embrittlement ..........and fabulously expensive .

 

[Gmonkee]

I used to stick weld on excavator and backhoe buckets. Nobody did it with wire feed I know of.

Deep V cuts and 7018 rods got hard plate to stick to mild steel. Even the Cat 320 excavators couldn't tear them apart. I think it was cranked up to 180 amps or so. Big Miller 3 phase welder.