Search results

Just picked up this Delta 12" Disk Sander. It's a 3-phase with a mechanical switch. I'll be running it off a VFD, but I'll keep the switch on to keep the originality. Can someone help identify this lamp that came with it? It looks like original to the machine. It's got the right shade of...

My 50amp breaker feed at the main panel trips before the subpanel on a 30amp 240v circuit. Shouldn't the 30amp breaker trip first at the subpanel? They're different brands: Square D QOs at the subpanel and standard GE at the main. Is the breaker at the subpanel broken?

I'm trying to restore a two vintage (1940s) Delta 710 motor (1/2 HP, 1 Phase, 1725 RPM). There are felt washers on the ends of the shaft that sits on each end of the bell housing. They are 1.625"x0.75"x0.125. I can't seem to find replacements, or maybe I'm looking at the wrong place. I'm...

If anyone has a picture of a switch rod for a vintage Delta 6" jointer on an open steel stand I'd appreciate it if you could post it. I'd like to fabricate one. I have the switch and the clamp, but is there a rubber bushing somewhere (per the 37-207 manual). I'm also looking at the right...

I'm looking for a particular switch with cover plate for a Delta motor. It's an on/off toggle switch with the toggle that is a flat blade with a hole on top. The hole is to attach switch rod so the switch can be turned off/on from another location. If you have that switch rod I would buy it...

Looking for a jointer stand for a Delta 6" Jointer 37-205 or 37-207. This is the splayed leg with the dust chute and belt guard. The catalog number is 50-656. I am in NY. Thx.

I have a KBAC 29D running my 2x72 grinder. I just installed a 14" contact wheel, but now I get a red status light, which, according to the manual, is an overload situation. The motor runs, then slows down, then stops. What exactly does overload mean? Should I increase the current limit to...

Sections of my concrete slab (outdoors) are sinking due to the base compacting or wearing away. It’s 20 years old but the sinking started several years after it was poured. Anybody use those companies that drill holes in the slab then spray an expanding foam to lift and level it? How long does...

I just broke my last 1/4“ drill bit so I’m ordering a set of a dozen 1/4” instead of just two to replace those broken ones in my drill sets. Then I realized instead of keeping those multi-size drill sets, I’ll just order a half dozen or dozen of 1/4”, 3/8” and 1/2” drill bits and standardize all...

My 2x72 grinder throws a lot of metal dust onto itself, the table and into the air and goes all over the garage and I have to breathe it. Is there a way to reduce it, or capture it better. I can catch the dust that goes directly down into a bucket or a dust collector bag right beneath the...

Hello, has anybody adapted the quick release tension lever from a Delta Bandsaw 28-475X to an older model 28-303? Any thoughts, caveats, advise? Thx.

I think this is the right forum for this: Fab and Techniques. Glued down a vanity side panel, but it kept popping out. Had to use what I had. Notice the technique. Feel free to copy......

Hello - I’m looking for a variable speed pulley (Reeves style) for a delta drill press 17-600 that fits on the motor side. This has a 1 1/2” bore at the bottom that tapers to 1” at the top. Only really need the bottom plate but I’ll take the entire pulley set if u have it. (Any leads are...

Moved to Wanted section ......

I have the lower spindle out from my Delta/Rockwell 17-600 drill press (1969 based on serial number). How do I remove these bearings? Use standard puller? or is there a trick to this? Also, how do I remove the MT2 spindle? Thx!

Searched and couldn’t find. Someone create one so I can post mine.