Search results

This is an old compressor from the 50's I believe. Its a Gardner Denver. It worked good till a valve broke and dropped in and broke one of the pistons. The other side still works and will produce pressure. But I'm selling this for parts. So if you want a challenge of rebuilding it or needs some...

Here's the details. I have an 80 Gal Tank, a 5 HP 3450 RPM electric motor with a 4 inch pulley. I just picked up an old Emglo KC model pump with the 13.5 inch wheel. With these numbers it's going to spin at about 1000 RPM which is within safe limits for this pump. And the specs say 4.5 to 8.5...

I'm selling this Airco Cutting Torch. It's style no 9505 but I can't make out the serial number on it. It's total length is 21 inches. Bob 847-767-0567

I am in need of a new compressor pump. I'm not too picky on specifics but i have an 80 gal tank with a 5 horse motor. So it needs to be decent size. I'm in the chicago land area and obviously will pick up. Thanks Bob 847-767-0567

I have this snap on gauge and adapters and box. 1 hinge is broken. It is for tranmissions and testing their pressures at different operations. Ive never used it but It should work. Im asking 75 bucks obo. Bob 847-767-0567

I have some old tools I no longer use. I'm ofering them for sale here. First is a Neihoff Voltage Reg. Tester and Book. dated 1953. This item works I used it on a few cars but don't have much use any more. I'm asking $100 bucks or best offer. Bob 847-767-0567

I have a Baldor single phase electric motor for sale. I needed one with more HP so this one is up for sale. 1725 RPM 1.5 HP 115V/230V 19A/9.5A This motor works good. Asking $100 obo or trade for air compressor pump or soda/sand blaster. Call,email, text Im not on here much 847-767-0567

I am trying to make some room and this lathe needs to go. It works great and is 42" long. It comes with the gears that give you the ability to cut threads. It has a 3 jaw chuck. It has a tag on it from the El Essley Machinery Co of Chicago. The lathe is at our shop in Plato Center about 40 miles...

I have a Gardner Denver single stage but 2 cylinder air compressor. That has a max output psi of 150 lbs. It has a 19" dual groove wheel on it. It came with a 1.5 HP Baldor motor that is wired to single phase 220v. It will turn and build pressure up to about 70 lbs and then the belt on the...

I am looking for the manual for a Sears Enginge Analyzer model # 161.214230. If anyone has one or a comparable one that would be great. If you can scan and email it that would be great or I'm willing to buy it too. Thanks, bob

I have a Gardner Denver Compressor Model ACDB9C9A. I believe that I need a pressure switch with an unloader valve because the compressor starts fine but when it tries to start with pressure in the tank/head the electric motor pulley spins and is unable to turn the compressor. I think that's...

I want to put a new panel in my garage 125A with 8 open slots. Currently there is a 30A with 2 slots. Also it's wired form the main box(in my house) with 8 ga to a junction box(just before it goes outside) where it turns into 12ga 3 conductor Romex. Then it runs to my garage 30A panel...

I have a Baldor electric motor to turn my Gardner-Denver compressor. The compressor looks old but the electric motor looks relatively new. I am trying to find a new safety switch and called Grainger and gave them my info they said that my electric motor is not big enough for the compressor. Is...