Search results

I'm no plumber... but what about a large loop under the floor (Basement Ceiling) and around the whole building, with Thermostatically Control Valves to control the flow into each room. That way you have a Thermostat for each room and the temp can be set independently. Also the Basement could...

Why don't you bolt it down on rubber pads ?

I run a 3/4" Main Line and Drops, 1/2" air hoses and some 3/8" hoses... all work great. I even used a 1/4" Coiled Air Hose that did everything I asked of it, air tools, painting, inflating tire, and jet of air ! The Air System loops around the Barn that measures, 32 x 36 feet, from the...

A lot of opinions... ! Back in New England I ran 300 psi, 3/4" rubber hose, worked great for the 15 years I had it and is still in use by the new owner. It is easy to setup, tight corners, easy to cut, clamps on barbed fittings, simple right. All you need to do is plan it out, count the pieces ...

The shop is finally all done, thank you Riverside, got the bases completed today for two benches and the sub top on one of them. Still need doors and electrics !

Thanks for the write-up ! I will be using the MaxLine for my whole system, easier to form to fit... I am hoping ! The main question I have is "Where is the best place to buy MaxLine" ?

Wastedwagerscing, Where did you end up with your shop ? Did you go Bison ? I did but regret it... a little !

The Costco units are bright... I was worried about the amount of lighting but it turned out well !

OP, Pattern..., I have not read all of the postings, sorry, time and opinions. Where do you stand on this now, have you changed anything ? If you haven't there is always a chance of fire ! Just an opinion, and everyone has one, you need to replace the control box you have and with a decent...

Miketoo2, I know this is an OLD thread BUT I am looking at buying a Gun Safe from this company. Was wondering what the end results were of your purchase. Anyone else have experiences with the Garage-Organization.com ? They appear to have a decent review level on the web. Thanks

I would use the rubber but make sure it is thick enough to handle the weight you MIGHT put on the rack.

I went to a. Local Costco in SoCa, they have them for $32 +tax. They had one on display at approx 7 to 8', the light output wasn't too bad BUT... What are they like at 13', which is my ceiling height ? Has anyone used these lights with a tall ceiling and how did they do ? I was going to buy...

Found a really nice Vulcan Amvil in a Pawn Shop; 100lbs, #10, sharp edges, no work fatigue. Looks almost unused ! (Actually weighs in at 105lbs). The symbol on the side is the Arm and Hammer with Vulcan on the top and a US Pat. On the bottom. Know nothing about it except that it will be a...

Did you finally buy a bison building ?

Things got delayed moving out to SoCal. The contractors in MA are just responding to the work I have... must be me ! Absolute has abandoned me so I have moved on to Armstrong. They appear to be good, the sales Rep has worked very patiently with me and I believe we have arrived at a design that...

I have a kit but do not know the manufacturer BUT I like it too ! The plugs are like mushrooms, that's all I know. Good tool to have around.

Did you break the link on both sides of the receptacles and on all of them ? Are the grounds hooked up on the GFCI breakers ? Are the Receptacle Grounds connected. I'm thinking the links on the receptacles. Luck

My house has almost all LED Lamps but this garage and the new one in California will not. Why... Because the cost vs life time of service does not equate to an overall lower price and my existing T12s hav been in there for almost a10 years. Why pay $75 per lamp. How many Fluor. lamps can you...

Thanks for advice. I still have no elevation drawing and this guy wants "paid in full" payment... Wtf ! Not sure what to do except as suggested in an earlier post... look around locally.

As suggest above drill a few extra holes in between the corner holes to relieve the stress on the Jigsaw and the actual time it will take to cut. Since the wall is ¼” it is thick, use a lot of lubricant and use the extra hole method.