Search results

Mine is a mix of freestanding, and attached the the building for support. Vertically it is completely supported by its own posts, I have attached it to the building where possible just cause.

2x12x16 can be spanned 16' on 16" centers for a 20lb dead load, 100lb live load. 12" center is probably overkill for your span. Attaching your joists is exactly how I built mine. For the post on the floor how thick is the floor currently? For my mezzanine I just pinned a 6x6 post onto the...

Nope, I used it as a Mortar. The product is basically epoxy, you just mix it with an aggregate. I ended up stripping the stuff down to the concrete, and just used another epoxy floor coating I had, mixed it with sand, and it setup in 8 hrs. No issues at all.

I think its all upside down!

I am super confused here. I ordered this from you. I was shipped a 5 gallon bucket with a bit less than 2.5 gallons of Part A, and a 1 gallon can a bit more than 1/2 gallon in it. I am not an installer, just a guy who ordered this off your website As for the mix here is what is on the can...

I spent a bit of time thinking about this over the weekend while trying to get this off the floor and has really left me wondering. I've been using Epoxy and Catalyzed lacquers for a few years with good results on automotive and wood applications where the mix is critical. I have never heard...

Well, I dont know what to think about this stuff. I spent a good amount of my weekend trying various things. After getting rather ticked off at my results I hosed it down with water to try to clean it up, then I hit it with the floor grinder to try to wet grind it off, this seemed to be the most...

You get 1 shot with concrete, a shop is not a good learning platform in my opinion. Fibermesh is not a replacement for steel in the slab, fiber will help with small hairline cracks, in my opinion it is a waste of money, stepping up to 4000psi mix is a better value. If you do go fibermesh you...

Well, I guess Ill get to scraping, I spent 3 hours today and barely put a dent in it. I fired up the grinder and that just gummed up the dymacerts. I just cant figure out how I would have messed up the mix, my last batch left me with 0 parts of A and B leftover, so if no excess of either...

I should clarify- None of the different batches I mixed setup, it is all tacky, some spots are more tacky than others, in some spots I can just leave a finger print, in other spots it will stick to my fingers. Ill get to scraping for now, I spread it out over a pretty large area, so this is...

I am not looking to bash any product here, I am not sure where the screw up occurred, just need to fix this mess... I laid down 3 gallons of Legacy HD110 Floor Patch mixed at 2 parts epoxy to 1 part washed/dried silica sand, the stuff never setup. It is still tacky 3 days later. I mixed 2 qt...

Crusher run density is usually around 2800lbs/yd Because everyone calls road base a different name depending upon where you are, I refer to it as "3/4 minus", which means 3/4" material and smaller, the density for something like this is usually around 2700lbs/yd I personally prefer 3/4 minus...

I used to live in Platteville, and had the exact same issue on my floor. The first step is to fix all of the drainage issues around your slab, and the mortar joints, this probably isnt where your issue lies, but should be repaired first. Next step is to make sure the floor is sweating due to...

Looks like an awesome place! My experience is pretty limited with solar, but the "off grid" solar systems I have been around require some pretty large batteries, especially if you are planning on operating power tools like a table saw. Batteries are expensive, and require replacement/maintenance...

This X2. My old shop in WI did this every spring, there was no stopping it apart from heating the slab in the wintertime. I nearly broke my neck on multiple occasions on that floor in the spring time, I would imagine an epoxy coating would only decrease the friction on the floor.

I am no pro on this matter, but I've spent quite a few hrs behind a grinder prepping my pad, and have painted quite a few cars with Epoxy. From the automotive side Epoxy requires 80grit scratches in bare metal for the epoxy to bite into. I have seen the results of not doing this, and it quickly...

How much sand do you mix in? 1:1 by volume? Or just until a slurry is achieved? Would you lay down a primer coat first? Or mix the sand into the primer?

I dont think run off is quite the right wording for my situation. He simply never came back, and chose to not answer my messages, phone calls, or get in contact with me in any way. I didnt pay him for all of his labor, he knows he screwed up, and knows what it would have taken to fix it. The guy...

Thanks, I will have to contact them as their largest kit is only 600sq ft

My contractor that poured my shop floor several years ago in Wi recommended that I seal as soon as possible when he was done pouring, I forget the name of the product, but it did say to seal once the concrete had setup enough to walk on it. I had spots that looked very similar to that, over the...