Search results

I’m not sure. 🤷‍♂️ Correct me if wrong, but I thought the sensor with the green light was “receiving” the beam, not sending it. I put a white piece of paper in front of both sensors and didn’t see any red, but rather just the green coming from the one sensor with the green light on. 🤔

The red light is NOT on. That’s why that picture baffles me. I’ll try cleaning up the connection and retightening. I cleaned off sensors with fresh shop towel, but yeah my initial thought was not aligned, but so far attempts to align failed. Do not see any spidey webs.

Hello all, I recently cleared out some items from behind my garage door sensor with the green light, which is still on. I don’t recall touching the sensor or it’s wires, but now the door will not close properly, it just keeps stopping and going back up, and I noticed the other sensor with the...

Thanks! Yeah, I found that also, but it doesn’t appear to show these parts.

Hello all, I have a Genie Model PCG650 - Chainglide garage door opener that apparently the previous owner took apart the Power Head Assembly, so I’m not sure if it works or not. I’m looking at the following motor parts, long metal piece that’s mostly square but round on one end, and has a...

Thanks! Yeah, apparently it was as simple as fixing the broken wire. 😉 FWIW: I’m using a CFL.

I attempted to realign the safe-t-beams, but I don’t believe that I did so, but some things that I noticed: 1) Both before & after attempting to realign the beams, the door reacts differently, depending on whether I try to close it with the remote vs. the wall mount. When I press & release the...

Thanks! Well, I may stand corrected. I DO have to continuously press the wall button to close the door, so I'll definitely have to re-check the alignment of the eyes and make sure the beams are pointing at each other.

Not a problem, I appreciate your input. Yes, the Genie remote use to bring the door down, when I first got it.

Thanks. The Overhead manual mentions the antenna twice; both mentions can be seen in the screenshot I posted, but it doesn't appear to tell me where it's located or how to adjust, "re-orient, or relocate" it.

Thanks. Correct me, if wrong, but if that were the case, wouldn't the door react the same when I used the mounted wall panel to close it?

Thanks. It IS a 3-button remote, and I followed the steps listed below in the Overhead Door Signature screwdrive installation manual to program a one button remote, primarily because I was a bit confused by what it says for programing a multi-button remote: "Repeat step 1 above 'Program...

Hello all, I have newer Genie G3T remote that I tried to program to work with an older model Overhead Door Signature Screw Drive opener. I followed the directions in the Overhead manual and the Genie now opens the garage door, but when I press the button that I programmed again, it briefly...

Thanks, SK & GJ! Count me in.

As for hub removal, the loaner kit (Evertough 67213 aka OEMTools 27213) I got from O'Reillys, has the following hub removal instructions (see page 3 of owner's manual, in text link above), which I believe is made to be done with hub still on car...Not sure about the Astro kit. HUB REMOVAL 1...

Thanks... BUMMER! :(

Hello all, To confirm, if you missed the August 7, 2017 Claim Submission Deadline, last year, that's it, you're out of luck...?

Thanks! Sounds like a big deal, to me...Nice job! Hopefully, you’re right on, about doubting the rust on a Florida car would be that bad. :fingersx::fingersx::fingersx:

Thanks, Jim...That’s very helpful! :thumbup: Yeah, rust ***** but I guess I’m going to have to see the actual e tent, at some point. That said, sounds like I need to do a bit more homework, on this type of fix...Cut out old & weld in new, before I turn her into Swiss cheese. ;)

Thanks! It’s this HF item by “Warrior” but 4 1/2, which says “Heavy duty polyurethane fibers with a fiberglass backing for extra durability”: https://m.harborfreight.com/4-in-polycarbide-abrasive-wheel-60508.html Yeah, that’s the sense, I’m getting. :(