Search results

Thx for the responses. These rod/plate brackets are to support sun shades over the windows on my new house. The shades weigh about 40 lb and will be supported by 4 of these brackets. I guessed at a load of 40 lb per bracket to account for wind load. The bracket screws to sistered studs with 4...

I am needing to weld several 1/2” threaded rod pieces(6” long) to 3/16” (3x6”) plates. All stainless using TIG. I tapped the plates and threaded the rod 2/3 of the way leaving a gap at the back to fill with weld. This was easy to weld and seems very strong. My question: is that sufficient...

I have a 1.5 hp pump set at 500’ . The owners manual says max wire length on 10# wire is 480’. The submersible wire already attached is 8# and 550’ long. I will call manufacturer tomorrow to try get amps of pump. All very confusing and frustrating. Thx for your help

Wyliesdiesels - are you saying 250’ is too long for the 6# cu or #2 au? Thx for your advice

Update and follow up question: So it turns out my utility will allow other conduits in the trench with a 30” separation. As such I plan on having them run the SE to the building and I will install another conduit to get pump power back to the well. I would like to this by running a 240vac...

Many thanks for all this helpful input. I will update when I hear from the utility, but this has helped me make a decision. Sent from my iPhone using Tapatalk

I am hoping to get some guidance on how to approach designing a new 200 amp service. My utility will run the 250’ of SE wire in conduit from electric pole to the building. I have to dig the trench. They place the meter on the building. However, I need electricity quite close to where their...

Ddawg16 Your list is very helpful, thanks. I wonder if you have updated it list since posting a year ago?

I was actually considering pouring my own pavers. Anyone have tips on the most economical way to do this? Sent from my iPhone using Tapatalk

Thx. What size pavers and did you make them or buy them?

I would like to install an apron on 2 sides of my metal workshop to facilitate moving things like a welding cart etc. ideally I would have done this in concrete when I poured the slab, but couldn’t afford it, so am now looking for cheaper options like pavers or permeable plastic driveway grid...

Thanks for all the response. I’m leaning toward the rolling stairs idea as it’s cheaper and safer. Sent from my iPhone using Tapatalk

I would like to build a sliding ladder to access loft storage in my workshop. Looking for recommendations for a supplier of hardware or complete system Sent from my iPhone using Tapatalk

Has anyone had experience with these? Sent from my iPhone using Tapatalk

Thx. Sorry to hear that. What would it take to remove it? Sent from my iPhone using Tapatalk

Thanks for the responses. I just found out that my contractor used this product immediately after it was poured. https://www.quikrete.com/productlines/concretesealer.asp Will this preclude using a densifier or other treatment? Sent from my iPhone using Tapatalk

My only reason for treating it would be to protect my investment by improving longevity. I don’t care about appearance. The floor will not be exposed to salt but I’m sure it will see oil and other fluid spills over time

I have a new 4”slab with fiber reinforcement. I want to treat it in the best way for longevity. I really don’t care about appearance as it’s just a tractor barn. One suggestion i received was to use this product. https://www.foundationarmor.com/concrete-hardeners-and-densifiers Anyone with...

HyperSelect Utility LED Shop Light, 4FT Integrated LED Fixture Garage Light, DLC 4.2 Premium Qualified, 35W (100W Eq.), 3800 Lumens, 4000K (Daylight White Glow), Frosted Cover - Pack of 4 Sent from my iPhone using Tapatalk

Thanks for all the responses and photos. Here are some bullets from my research: Not all foams are created equal. Installation skill and attention to humidity during application are important I read anecdotal material online about manufactures not warrantying foam installations but the ones I...