Search results

I really like my Shaviv deburring tools. If you have trouble getting the Noga, maybe take a look at them...

The chlorine compounds emitted by standard brake cleaner when burned are extremely toxic, so it's good that you are concerned. There is a non-chlorinated version of brake cleaner, though, that you can buy off the shelf at most places that sell it. If you get the non-chlorinated version, no...

If you want the cleanest air with no moisture problems and such, no fumes, and no oxygen depletion, I would suggest a sealed combustion propane heater. These units also do not create negative pressure in the building, so they work more efficiently. You will have to get your propane filled up...

I certainly considered leaving the fiberglass. In the end, though, the extra weight was not worth it to me, just for appearance. Mine is just a home shop, used mostly for metal fabrication and car repairs. If it was a business, I might have considered the extra weight worth it, for appearance...

I insulated the inside of my roll-up doors with foam panels that I got for free. There is an insulated door manufacturer locally here that often has rejects pulled from the line. Rather than paying to have these hauled off, they palletize them and give them away for free to any taker. We got a...

I always have a few extra rounds of 10mm rolling around in the center console of the truck...

We work on valves for large oceangoing vessels. It's not really anything mysterious. It's fairly standard work in the industry. Disassembly and reassembly is just basic wrench-turning. The honing and seats are fairly standard machining procedures. The honing is done on a spherical hone. We take...

Not worth trying to disassemble. They use threadlocker on them. They don't want you messing with them, because the stack height in there with the seats is super critical, and easy to mess up. I work in a shop that rebuilds larger ball valves all the time (3" to 12" balls). We hone and teflon...

When I picked up my 2-post, the lift was packed so that it was an "end pick" by the forklift. They came right out of the bay and put in on the trailer. If yours is packed that way, you could use the Home Depot truck and put some blocks on the back. As long as the tops of the blocks are higher...

I have a Fluke 23 that I've owned for almost 30 years. Works well for almost all of the above. No backlight, no capacitance, though.

Perhaps here? https://amesweb.info/StructuralAnalysisBeams/Stresses_Steel_Hollow_Structural_Sections.aspx

I've had grit in the lines before, and it caused my regulator to develop a "creep" problem. That is easily dealt with at the regulator, but I would not want to have that at the heater valve. That is less easily dealt with. I put a tee trap in mine. I have a Modine PTC-65 running off of two 40...

We are a heavy industrial shop here. We usually use Sherwin-Williams Armorseal 8100 on our floors. We don't use it because it's the best, we use it because it's relatively cheap. We repaint the floors about every 4 or 5 years in here anyway. It holds up great in areas of regular foot traffic...

I haven't bought diamond wheels from Shars, but I've bought endmills from them, and I bought a 4-jaw chuck from them once. I have been satisfied with all of those purchases. The chuck was actually of surprisingly high quality for an amazing price.

I ordered mine from H-Mac systems. They were great to work with. They are a drop shipper, so it's up to the manufacturer, but they got mine to me in a reasonable time. (It's a Modine PTC-65, set up for propane).

You should be able to retract the piston enough to get it off the rotor without any special tools. You just won't be able to retract it enough to get new pads in there without the tool. I usually just rent the kit from Oreilly Auto Parts. The rental is actually free. You put a deposit on it...

American O-ring boss fittings are made per SAE J1926-1. If you look that one up, you will find the spec. They are a straight thread, not tapered like NPT. They have a specific cut in the sealing area for the o-ring to seal. If you are just looking for the fittings, any hydraulic hose shop...

Have a Black & Decker Quantum Pro 18v drill that I've had for... certainly more than a decade, but not sure exactly. That and lights are the only cordless tools I use. I actually PREFER corded tools for stuff around the shop. I only use the cordless when I'm outside. I've replaced the batteries...

For blind holes, there is not much better on the market, in my opinion, then Time-Sert. I have used them repeatedly to repair spark plug threads, and while they are a bit spendy, they are phenomenal for difficult thread repairs that require significant post-repair strength. I have the spark plug...

Welcome from the wet side of the mountains. Hope you stay safe from the fires up there!