Search results

Im southcentral Va. and looking to have mine redone - did you have yours redone yet? All- I just got a quote this AM to have driveway re-surfaced. Said they would cut a 4" wide "trench" to the base at "tie ins" (house garage and detached shop concrete apron) then grind/mill a 2' foot wide X...

Oops. Yes - I put that in for temp outlet while I worked and plan to install a WR exterior outlet in that corner in its place. Thanks for pointing that out…I guess I’d realise it was behind insulation eventually!

For the HVAC I had a lot of #10 UF that I wanted to use up. For the loft stove I used 8/3 UF becasue it was $3 per foot vs $6.28 per foot for NM. As to the feeder I cant say why the retired electrician ran it that way and it was a pita.

Not finished but plodding along. Wiring and insulation finished and hope to ave drywall delivered this week and then hopefully have it installed next. There are a few more photos on progress in the mini split post. I did not install a sub-panel or do any of that stranded the electrcian mentioned...

Thanks - Wall height in garage is 10ft loft is 8ft roof is 12/12 pitch. I tinkered with the design quite a bit as covid pushed the start date. There are definitely a few things I would change but all in all im pleased. I'll finish insulation tomorrow in garage level and that will be complete...

Due to my wall configuration in loft (photo above) Im looking at the pioneer floor/ceiling mount unit. Anyone have any opinions on Pioneer and/or floor/ceiling mount units?

Ok thanks others mentioned two units as well. Wiring is not a problem. What’s your opinion on the “floor standing” and locating it to the left corner of dormer? Any opinions on the mr cool losers or pioneer at HD or other place’s to source DIY pre charged?

Thanks for that info - had not seen those. Just now searching them and also see "floor standing" units which could also work. Was trying to keep head somewhat centered in the loft area - maybe that doesn't matter. Ive never had mini split so new to me. Also kind of indecisive on whether or not...

I contacted my residential HVAC company for a quote on a standard economy grade heat pump as well as quote for his recommendation on a mini-split. He said the mini-split was the way to go and opted not to quote the heat pump at all. Anyway I was floored by the quote: install RUN-Tru by Trane 2...

Thanks for all the feedback! Good idea on using nail plates (assuming they are still reasonable in cost!). Im flexible on the 40" (36" ht of my planned work bench). Interesting thought on >48" to stand drywall on it side but if there are say 10 other outlets it probably wouldnt be an issue to...

Thanks for the response. I was planning on running outlets in garage at 40" from floor and in the loft area 18" from floor.

2X6 studs in garage level and 2X4 studs in loft area. What is the required code min/max distance for holes from face of stud for routing Romex? Also.. What is the required code min/max distance for receptacles from concete garage floor?

Hhahahahah!! Ive looked all over for a crank handle for that old workhorse!!!

Just looked up them up and see that now. He also drilled two holes next to each other in the top plate for conduit but only used one. Guess I'll never know what hewas thinking!

Edit* Loft has access through a garage side door then a door to go up the stairs. Its intended for guests and possibly future rental to someone vetted who can help out around the house for reduced rent. Our 3 bedroom ranch is adjacent to the new garage. Our septic tank is 1500 gallon but the...

Glad I asked for opinions on his conduit/stranded wire idea - its now dead to me. I'll look into the requirements of whatever small "apartment" size appliances we plan to put up there and run romex accordingly.

Sounds good. Thanks for the advice. So...with one 10/3 the stove and the mini split would be on the same circuit?

Ok - I talked to the guy today. He said (if he were wiring the loft area) he'd run 6 pairs (for 6 circuits) of #12 stranded through 3/4" conduit from the panel in the garage to a junction box in the loft then from the junction box run romex to the outlets, lights switches etc. for each circuit...

Thanks for the response. Assuming I follow you on this.... two different units...one 20k BTU for garage and a 15k BTU for loft. I think I will have space for a single head for garage and a single head for loft. But - since they will be for two separate areas - how could reduncancy be applied if...

Good point. He’s supposed to be here tomorrow so I’ll either clarify or muddle the water further!