Search results

Yes, this is acoustic metal, not soffit metal. This is specific for use inside a building, just curious on the negatives to doing it on a ceiling vs top of walls. My lights will be recessed between the trusses so they will be flat to the ceiling, not below the metal

It doesn't say the open percentage, here is the link. https://www.menards.com/main/building-materials/pole-barn-post-frame-materials/steel-panels/white-acoustical-liner-panel/white1558185/p-1444448678798-c-5717.htm?tid=-1480537518223266793&ipos=1 I am getting it for 8 bucks per 16 ft sheet, I...

Anybody do the white liner tin on their entire ceiling? I am looking at doing a white vapor barrier, then the perforated liner tin with recessed 2x4 LED lighting between my trusses, then blow in insulation. My building is a 32x68 with a 3/12 vaulted truss inside, stick build Thoughts?

Here it sits, I now have tar paper on and will put ice and water on the edge when the snow blows off. I am hoping to start shingling in the next couple weeks depending on temps. The building will match my house, same color, siding, doors, etc as well as the stone on the front. The house I had...

Driveitsfar, Thanks, those are not mine, I do side work to pay for my shop. I primarily do body work, but at times, I will get requested to do the whole job. I have two more coming in, so I hope to move along pretty fast on my shop if all works out well. When I had teh foundation sitting...

last batch

more

1979 bronco and a 1956 ford

here is some of the past work I have done, new work will be done in my shop, hopefully next year

well, one week and the framing is all wrapped up. Primarily it was three of us, on a couple days we had a fourth. Now I start finishing up the interior wall framing, end gables inside for the vault so I can set up for sheet rock and liner tin. Depending on weather, I may start roofing in a...

The pics are from this morning, beautiful day to be outside. We sheeted 3 sides and started setting trusses, tomorrow, we should have the trusses on and sheeted

well Today was a wash out, rain in December in MN = no good We finished up a couple walls, hopefully tomorrow is a good day, get the front on and start sheeting,,,,we will see if Mother nature agrees!!!! More pics tomorrow

Well After 9 years of working my **** off and saving, I am finally building my shop. Short story 10 years ago my wife and I bought our land, we built our house, did about 60% ourselves, GC'd out the rest. I prepped up to build a 32x68 with room in attic trusses (county would not go more than...

where did you get the door track that follows your vault? Did you make them? Nice looking shop!

Thought I would give you an update,,,,decided to use the 250 xps, I went to a local lumber yard in st peter, MN, they can do it for me at $26.00 per sheet, menards was 30.53. I have more sand and gravel coming this week, 3 tri axle loads,,,,,hopefully will get me up to grade so I can get it...

Badger What do you recommend for foam under a slab, the 15 psi or the 25 psi? I have spoken to a friend who is a structural engineer and has done jobs that require foam under a footing, they use the 25 psi xps. I spoke to him about what to use, his feeling was that 15 psi xps would be...

Thanks, It will be a working shop, 4 post lift which sits on 12x12 pads, my super duty pick up would probably be the heaviest thing on there,,,,,the rest are cars and light duty trucks...... According to teh menards website, to go from XPS 15 PSI to xps 25 psi is less than a dollar...

my dad use to design in floor heat systems and designed my system and found with the length of runs, temps, size of building the boiler, etc ended up that 5/8 would work best. Back when he designed it, a product called insutarp was teh hot ticket for insulation under the floor. My reccomendation...

Let me re-phrase my question, I already am planning on insulation under my floor, do I need to use the high density or can I use regular styrene? I ask because I can get 4x8x 3 inch styrene for 5 bucks a sheet, but it isnt the high density.......I have read and understand there is a...

I am in the process of building a 32x 68 shop, I have the footings/ block in, 50 inches deep with 2 inch styrene on the inside and 1 inch on the outside full depth. I have about 12-18 inches of sand that has settled thru the winter and been compacted for the floor to sit on as well as a ledge...