Search results

Bttt obo

Sold

This is an old compressor from the 50's I believe. Its a Gardner Denver. It worked good till a valve broke and dropped in and broke one of the pistons. The other side still works and will produce pressure. But I'm selling this for parts. So if you want a challenge of rebuilding it or needs some...

75 obo

The pump HP according to the site says it can be run using anywhere from 3/4 HP to 5HP. I have a 5 HP. The motor will definately turn it. Mininum RPM is 550 and max is 1150 RPM. I will be running it at about 1000 RPM however I can't find a PSI rating for the CFM.

Here's the details. I have an 80 Gal Tank, a 5 HP 3450 RPM electric motor with a 4 inch pulley. I just picked up an old Emglo KC model pump with the 13.5 inch wheel. With these numbers it's going to spin at about 1000 RPM which is within safe limits for this pump. And the specs say 4.5 to 8.5...

Bttt obo

Bttt obo

Bttt obo

Bttt obo

I'm selling this Airco Cutting Torch. It's style no 9505 but I can't make out the serial number on it. It's total length is 21 inches. Bob 847-767-0567

I am in need of a new compressor pump. I'm not too picky on specifics but i have an 80 gal tank with a 5 horse motor. So it needs to be decent size. I'm in the chicago land area and obviously will pick up. Thanks Bob 847-767-0567

I have this snap on gauge and adapters and box. 1 hinge is broken. It is for tranmissions and testing their pressures at different operations. Ive never used it but It should work. Im asking 75 bucks obo. Bob 847-767-0567

I have some old tools I no longer use. I'm ofering them for sale here. First is a Neihoff Voltage Reg. Tester and Book. dated 1953. This item works I used it on a few cars but don't have much use any more. I'm asking $100 bucks or best offer. Bob 847-767-0567

I have a Baldor single phase electric motor for sale. I needed one with more HP so this one is up for sale. 1725 RPM 1.5 HP 115V/230V 19A/9.5A This motor works good. Asking $100 obo or trade for air compressor pump or soda/sand blaster. Call,email, text Im not on here much 847-767-0567

I am trying to make some room and this lathe needs to go. It works great and is 42" long. It comes with the gears that give you the ability to cut threads. It has a 3 jaw chuck. It has a tag on it from the El Essley Machinery Co of Chicago. The lathe is at our shop in Plato Center about 40 miles...

I replaced the motor becuase the original was long gone and when I got it, it had a 1.5 HP and that's not enough to turn the motor. I was able to get proper tension on the belt and now it's either a compressor or pulley problem. It's a single stage 2 cylinder. Bob

OK I put a 3 HP motor that spins at 3450 RPM. It fills up quite quickly to 60 PSI but after that it struggles and takes around 5 minutes to build 10 more PSI. I have a 1.5 inch motor pulley and 19" compressor pulley. I know I need a 4 inch motor pulley but can't find one with a double groove...

I have a Gardner Denver single stage but 2 cylinder air compressor. That has a max output psi of 150 lbs. It has a 19" dual groove wheel on it. It came with a 1.5 HP Baldor motor that is wired to single phase 220v. It will turn and build pressure up to about 70 lbs and then the belt on the...

Ok I have it all wired and plumbed up but I still have a problem I think. When the switch is on and the compressor is running it works fine no leaks. But when I turn the switch off the unloader valve begins releasing air even if I only have 20lbs of pressure in the tank. Is this normal or is...