NEW Craftsman Professional Polished Metric Wrench Set 7MM-19MM + 3 New S-K 20,22,23

MOPARHOUND! · Feb 3, 2009

SOLD! SOLD! SOLD!

Thanks GJ.com!!

SOLD! SOLD! SOLD!

Thanks GJ.com!!

Wrenches are new, never used. Some may have minute shelf wear (see back side of S-K 20MM open end, only see it held up to light). The Craftsman 7MM to 19MM are "long pattern" wrenches (roughly the length of a standard Snap-On wrench), with the S-K wrenches being regular length. The Craftsman 7MM to 18MM have extra thick beams through most of their length, don't think this is available from Craftsman any longer in this style wrench. The 19MM is like Craftsman's current offering (see pic's). The S-K sizes are 20MM, 22MM, & 23MM.

Front:

Back:

Delivered to your door for $109.95, I'll pay the shipping and the Paypal fees. :thumbup:

(S-K's Also available in several separate 3 piece lots, $39.00 shipped to your door: http://www.garagejournal.com/forum/showthread.php?t=29498 )

Thanks.

ProGun3400 · Feb 24, 2009

don't think this is available from Craftsman any longer in this style wrench.

No they're not. These are a much beefier wrench than the new style IMO. I've spread the jaws on a few of the newer style. I have a few in this style and I prefer them. :thumbup:

fourfeathers · Feb 24, 2009

I wonder if those Craftsman are made by Bahco.

Tool Pants · Feb 24, 2009

When the stubbies first came out the beams were flat. Then they went to a slight raised panel look and that is the current version.

I have a set of the long pattern and they are flat like the 19mm in the picture. The 7-18mm looks like they have a slight raised panel, and I do not remember those. What is the part number on the 18mm?

MOPARHOUND! · Feb 24, 2009

The 18mm part # is 42262. The 19mm part # is 44909.

rsanter · Feb 24, 2009

didnt a set of those early Cman pro wrenches just sell on ebay for stupid money?

I wonder if you are better off selling those as a set and then the other 4 seperatly

bob

cruiser808 · Feb 24, 2009

Tool Pants said:
When the stubbies first came out the beams were flat. Then they went to a slight raised panel look and that is the current version.

I have a set of the long pattern and they are flat like the 19mm in the picture. The 7-18mm looks like they have a slight raised panel, and I do not remember those. What is the part number on the 18mm?

I have SAE and metric sets of the older flat Cman stubbies. I believe they were made for Sears by S-K. A year or two after I bought them, Sears came out with the polished semi-raised panel version. I like my version just fine.

Tool Pants · Feb 24, 2009

My 18mm is 44908 so the part number changed when the raised went to flat. My 19mm is 44909, like your flat 19mm. As I said, I did not remember that there was an original version in raised panel long pattern fully polished. Probably because I did not have the money for something that fancy back when they first came out.

The older flat stubbies I remember because I almost bought a set when they were being cleared for the raised panel version.

Bull · Feb 24, 2009

This set of wrenches is painful for me to look at. So nice!

MOPARHOUND! · Mar 3, 2009

SOLD! SOLD! SOLD!

Thanks GJ.com!!

mtwaterguy · Mar 5, 2009

Got the wrenches today. Just as described with great packaging and shipping. Thanks, Mike.

NEW Craftsman Professional Polished Metric Wrench Set 7MM-19MM + 3 New S-K 20,22,23

MOPARHOUND!

Well-known member

ProGun3400

Well-known member

fourfeathers

Well-known member

Tool Pants

Well-known member

MOPARHOUND!

Well-known member

rsanter

Well-known member

cruiser808

Well-known member

Tool Pants

Well-known member

Bull

Super Moderator

MOPARHOUND!

Well-known member

mtwaterguy

Well-known member