To avoid these ads, REGISTER NOW!

Above 1200 Sq/FT The Cow Pasture Garage - Australia

Wokspaces above 1200 squarefeet.
OP
K

kitdoctor

Well-known member
Joined
Oct 30, 2010
Messages
531
Location
Sunshine Coast, Australia
Tropical Cyclone Fina was upgraded to a Category 3.

The Bureau of Meterology describes a category three cyclone as having "very destructive winds", with a maximum mean wind speed of 118 to 159 km/h (74 to 100 mph) and typical strongest gusts of 165 to 224 km/h (103 to 140 mph).

If there's good news, the cyclone is very tightly wound up.

Tropical Cyclone Forecast Track Map Fina 22 November 2025 4 pm.png
 
To avoid these ads, REGISTER NOW!
OP
K

kitdoctor

Well-known member
Joined
Oct 30, 2010
Messages
531
Location
Sunshine Coast, Australia
the cars of the '50s and '60s were the best decades of my car life life
@Bob Heine can't disagree with that but I'll add in the early 1970s.

My favourite car of the 1950s has to be the 1957 Chevrolet Nomad. It's my understanding that it emerged from Chevrolet's Corvette Nomad or Waldorf Corvette displayed by Chevrolet in 1953.


I built the Revell model kit as a kid. The box artwork was at a real high point during the 1960s and the first edition of the kit doesn't disappoint. I have another build that I commenced pre-2009 that I'd like to resurrect one day. The plan was to replicate the car shown on the box artwork but with a 502 cubic inch resin engine.

Revell '57 Chevy Nomad Photo No. 1.png
 
Last edited:

Bob Heine

ALLIANCE MEMBER
Joined
Oct 24, 2009
Messages
10,708
Location
Boca Raton, Florida
It just shows how important it is to address/minimise the gaps. That's an enormous saving. When you think about it, your understanding of sealing the gaps and increasing the thermal efficiency of your home was light years ahead of building codes/standards/current thinking.
Joel, I didn't really understand how important the ceiling insulation was when I started. Our master bedroom in that house was in the left side wing so it had three poorly insulated walls. We moved into the house in July so the two large fans in the attic did a wonderful job cooling the house down to whatever the outside temperature was. When winter arrived, Liane complained that the bedroom was always freezing cold. I kinda liked it but decided to test the effect of better insulation starting with that room. Our finances allowed for three bundles of R19 foil faced fiberglass insulation. I started the process one evening and went into the attic, which was warmer than the living space. I assumed the warmth came from the sun beating down on the roof during the day.

I started the insulation install at the front (window end) of the room, wearing a light t-shirt and jeans. The three bundles filled two thirds of the ceiling bays but before I reached the halfway point I had to quit and put on two layers of long sleeve jumpers because the attic temperature in the wing over that bedroom was suddenly close to the outside temperature, a bit below 0°C. I finished putting the bats in and put enough R19 bundles on our credit card the next day to finish the bedroom wing. The bedroom became so warm I had to adjust the forced air duct in the room to prevent being roasted alive. It took a few months to finish the rest of the house. I refused to put more on our charge card than we could pay off in full, a nasty habit that continues to this day.
 

Bob Heine

ALLIANCE MEMBER
Joined
Oct 24, 2009
Messages
10,708
Location
Boca Raton, Florida
The Bureau of Meterology describes a category three cyclone as having "very destructive winds", with a maximum mean wind speed of 118 to 159 km/h (74 to 100 mph) and typical strongest gusts of 165 to 224 km/h (103 to 140 mph).
Joel, I try not to freak out over tropical storms but whenever a storm is named in the Atlantic I head to the NOAA (National Oceanic and Atmospheric Administration) National Hurricane Center and Central Pacific Hurricane Center to see where it is headed. They only track storms near United States territory so I only find out about your Cyclones when a news outlet or someone on the GJ mentions them.

A few weeks ago I started tracking Melissa. The projected path indicated it wouldn't make a direct hit on us but Hurricanes don't always follow our projections. Thankfully Melissa stayed on track but holy ****, it went from a Tropical Storm to a Category 5 Hurricane in less than two days.
Melissa Track.jpg
Watching the storm wobble (in the blacked out zone) in real time before it intensified didn't lower my anxiety. Sustained wind speed of 185 miles per hour (298 kilometres per hour) when it reached Jamaica was bad but one gust on October 28, 2025 was recorded at 252 mph (406 km/h). I suspect nothing survives a blast like that. And that gust is the highest ever recorded in a Hurricane.

I'm hoping (and speaking to my invisible friend) that Fina spares damage to your Darwin home. I look at your storm images with my southern hemisphere brain cells and it looks like Darwin is on the worst side of the storm (left front quadrant). Just read that a section of the Royal Darwin Hospital's roof collapsed. No injuries to staff or patients but still, scary stuff.
 
Last edited:

Bob Heine

ALLIANCE MEMBER
Joined
Oct 24, 2009
Messages
10,708
Location
Boca Raton, Florida
@Bob Heine can't disagree with that but I'll add in the early 1970s.

My favourite car of the 1950s has to be the 1957 Chevrolet Nomad. It's my understanding that it emerged from Chevrolet's Corvette Nomad or Waldorf Corvette displayed by Chevrolet in 1953.
Joel, you're right, the early 1970s had some great cars. My '71 Vega GT had chrome bumpers mounted close to the body. Each subsequent year saw the bumpers move and then morph in to the hideous 5mph bumpers that ruled the mid to late 1970 Vehicles. My '72 Corvette has the chrome front bumper that was replaced with an Endura urethane front nose. I didn't hate the Endura cars (our '68 GTO was the first for GM) but it seems like a downgrade from elegant to ugly.

You brought a tear to my eye with the Nomad model. In 1964 I came across a '55 Nomad that was "rust-free" by Rust Belt America standards. It had a 265ci V8 and two-speed Powerglide automatic. I had saved up $300 for a car but the guy wanted $700 and wouldn't budge. Had I been willing to hold up a 7-11 it could have been mine but even though it was a decade before the phrase "don't do the crime if you can't do the time" appeared (in Baretta) it wasn't in my nature. Neither was borrowing money to buy things.
 

Bob Heine

ALLIANCE MEMBER
Joined
Oct 24, 2009
Messages
10,708
Location
Boca Raton, Florida
Joel, I'm hoping my posts are distracting you from doom-scrolling for storm updates. All we can do is watch and hope. No matter how well you plan and prepare, it's like Mike Tyson supposedly said: "Everyone has a plan until they get punched in the face."
 
OP
K

kitdoctor

Well-known member
Joined
Oct 30, 2010
Messages
531
Location
Sunshine Coast, Australia
I've robbed a few photographs from the ABC (Australian Broadcasting Corporation the official national emergency broadcaster).

This is in the CBD on the corner of Smith Street Mall and Knuckey Street. On the LHS out of view is a motel/commercial building, Darwin Central that houses McDonalds 🍔, a coffee shop etc. On the RHS, that's the old converted Woolworths supermarket. That's an African Mahogany that's fallen over. These were planted after Tropical Cyclone Tracy in 1974, as they're quick growing. The problem is they're shallow rooted.

Tropical Cyclone Fina Photo No. 1.jpg

This is in Cavanagh Street. On the RHS is the Northern Territory Local Court. On the LHS out of view is the ABC broadcasting studio.

Tropical Cyclone Fina Photo No. 2.jpg

This is looking beyond the Northern Territory Local Court, further down Cavanagh Street. Years ago the council had this idea to make the city greener and cooler and built this canopy over the street. The idea was a creeping vine would grow over it. Obviously, that didn't work.

I worked in a couple of multi-story buildings in this street located either side of the hotel 🍻where the cars are parked.

Tropical Cyclone Fina Photo No. 3.jpg

This is at the main city bus stop just around the corner from the Northern Territory Local Court. On the LHS is the ABC broadcasting studio.

Tropical Cyclone Fina Photo No. 4.jpg

Here's the base of that fallen tree outside Darwin Central.

Tropical Cyclone Fina Photo No. 5.jpg

This one's just on the opposite side of that fallen tree, maybe a little further down Smith Street.

Tropical Cyclone Fina Photo No. 6.jpg

Back at the main bus stop.

Tropical Cyclone Fina Photo No. 7.jpg

In the Smith Street Mall outside the historic Victoria Hotel.

Tropical Cyclone Fina Photo No. 9.jpg
 
Last edited:
OP
K

kitdoctor

Well-known member
Joined
Oct 30, 2010
Messages
531
Location
Sunshine Coast, Australia
After the last 2 days, I am beginning to think that may not be so. :sad:
@Mr onetwo, I look at my build this way. I just keep taking small steps forward and yes, sometimes there are set backs but so long as you keep thinking ahead, finding solutions and solving problems you end up actually getting closer to the end.

As I mentioned, my electrical contractor has disappeared, so I tried my builder's electrical sub-contractor who did my internal fit out but he was too busy. I then contacted another local electrician five times. Yes, they said they'd come and quote on the project but they never committed to a visit. So, I went back to my builder and he gave me the number of another local electrician. He came out the day I contacted him and connected up the electricity to the WwTP system on the Tuesday just gone. The system now works and the toilet is now working🚽

I can now organise for the contractor that installed the WwTP system to officially commission it. They can advise the local council it's operational which then allows council to undertake a final inspection of the plumbing and drainage works.

So, with persistence you get there.
 
OP
K

kitdoctor

Well-known member
Joined
Oct 30, 2010
Messages
531
Location
Sunshine Coast, Australia
Joel, I'm hoping my posts are distracting you from doom-scrolling for storm updates. All we can do is watch and hope.
@Bob Heine we couldn't help ourselves and had to listen to the local ABC radio broadcast (via the internet) and watched the ABC Northern Territory news at 7:00 pm CST.

By all reports the worst was due from about 8:30 pm CST onwards, so to distract ourselves we plonked ourselves in our friend's IMG recliners and started watching the third season of the psychological thriller The Sinner on Netflix. Not my words but it's a "why-dunnit" twist on the traditional murder mystery plot.

 
Last edited:

Geoff289

Well-known member
Joined
Nov 10, 2013
Messages
1,235
Location
Melbourne, Australia
By all reports the worst was due from about 8:30 pm CST onwards, so to distract ourselves we plonked ourselves in our friend's IMG recliners and started watching the third season of the psychological thriller The Sinner on Netflix. Not my words but it's a "why-dunnit" twist on the traditional murder mystery plot.
The Sinner is pretty gripping isn't it Bob? We've watched all four seasons. Like so many, I reckon the first season was the best.
 

Bob Heine

ALLIANCE MEMBER
Joined
Oct 24, 2009
Messages
10,708
Location
Boca Raton, Florida
The Sinner is pretty gripping isn't it Bob? We've watched all four seasons. Like so many, I reckon the first season was the best.
@Geoff289, I think it's pretty good too lol
Geoff and Joel, the benefits of getting old are few but I do get to watch movies and shows a second or third time and get real far into the drama before I remember the ending. I agree with Geoff that the first was the best.

Real glad Fina didn't make a huge mess for you.
 
OP
K

kitdoctor

Well-known member
Joined
Oct 30, 2010
Messages
531
Location
Sunshine Coast, Australia
Real glad Fina didn't make a huge mess for you.
@Bob Heine me too, though the Tiwi Islands didn't fair so well. Not seeing much press on that though.

Just watching the news, response crews said there's about a one week of work (in Darwin) cleaning up debris, fallen trees etc.

I saw a reporter interview a guy who said Fina was worse than Tropical Cyclone Marcus in 2018 which I immediately jumped on and was saying no way. The clean up after Marcus took months. There were so many trees felled that de-centralised timber stock piles were created all over the city and debates raged over how the timber could be used, rather than being chipped.
 
OP
K

kitdoctor

Well-known member
Joined
Oct 30, 2010
Messages
531
Location
Sunshine Coast, Australia
Post #0057 - Construction work continues - Plasterboard and cornice installation - Part LII

With the insulation batt install completed, next up was the lining of the accommodation module’s walls and ceiling.

This next sequence of photos shows the four basic walls of the downstairs area of the accommodation module. At this point, the plasterboard wall and ceiling sheets were installed and the joints between sheets had just been done and were drying.

First up is the main kitchen wall, which faces east. The window provides a view over the eastern part of the block including the dam. To the right, you can see how one of the portal frame columns was boxed in.

The doorway on the left leads to the internal staircase and the bathroom. If you look closely, you can see how the wall here with the doorway opening aligns with a major column. This column has been boxed in and meets the narrower stud wall above the door opening, creating a small offset where the two join.

Why the emphasis on this? Well, if all goes to plan, a sliding barn door will be installed and still fit nicely here. Barn doors are normally fitted in situations where the walls either side of the door opening are within the same plane. The challenge here will be that it will close against the narrow piece of wall. The installation will also throw up one other challenge, not obvious at this point in time. What do you think that might be?

Post #0057 - Photo No. 1.jpg

To the right is the wall that has a glass sliding door that leads out onto the external patio. A 2700 mm (9’) high glass sliding door was installed, instead of a standard 2400 mm (8’) door just to let more light in and provide a better view of the outside.

Post #0057 - Photo No. 2.jpg

Spinning further around is the main wall of the living room against which the television will sit.

Post #0057 - Photo No. 3.jpg

Continuing further around is the wall behind which there’ll be a staircase leading upstairs to the bedroom. The staircase creates the space for the laundrette in the stairwell and some stairwell storage. To the left, the doorway exits to the main area of the shed.

Post #0057 - Photo No. 4.jpg

One of those small details was the choice of cornices. What I did was to select two, both different to the typical, standard cornice used in homes. The first was Gyprock's Alto which is used in the main downstairs area. It’s slightly more sophisticated/ornate and has a 10 mm step along the ceiling edge which creates a shadow.

Post #0057 - Photo No. 5.jpg

The cornice used in all other areas was Gyprock's Aria. This is a slightly simpler cornice but includes a subtle central deflection. Here it’s shown in the upstairs bedroom where it’s also possible again to see how a major corner column was boxed in.

Post #0057 - Photo No. 6.jpg

The laundrette does not feature a cornice, so it’s square set. This is necessary because the underside of the staircase will create a partially sloped ceiling, so any cornice placed at an angle would look odd.

Post #0057 - Photo No. 7.jpg

Back in post #0055a there was a photo of a corner in the living room that had a SHS with a base plate that had to dealt with because the base plate intruded into the floor area. Here’s the photo from that post.

Post #0057 - Photo No. 8.jpg

Here it is neatly finished. Once tiled, this will lift the skirting board off the slab floor and they’ll be cut at an angle, to neatly meet the angled corner.

Post #0057 - Photo No. 9.jpg

That’s about it. Once a substrate staircase goes in the plasterers will return and line the underside of that within the laundrette to create the sloped ceiling of the laundrette.

Final comments. Damn messy trade. We had the place spotless and you end up with blobs of plaster, flakes and dust everywhere🧹 🪣.
 
Last edited:
To avoid these ads, REGISTER NOW!
OP
K

kitdoctor

Well-known member
Joined
Oct 30, 2010
Messages
531
Location
Sunshine Coast, Australia
Post #0058 – Backpack sprayers – Solo 475 vs Silvan ProGrade - Part LIII

Hi everyone, this post is a deviation from the normal updates. I thought I’d do a short review of the two backpack sprayers we’re using to spot spray weeds. They’re just some of the equipment that is essential for controlling weeds when you’re on acreage.

I ummed and ahhed about whether to do it, but in the end I allocated a post number to it in my list of planned posts and I didn’t want to renumber the list and all the draft posts I have in progress if I didn’t go ahead with it.

Where I can, I have a tendency to buy German designed/engineered products and it’s even better if they’re manufactured in Germany. The other alternative is Japanese products. Why? Well, I simply believe the products are better in many aspects. Better design, better quality and last longer.

So, it was from this starting point that led us to purchasing a Solo sprayer. Our local hardware and produce store had the model we wanted at a competitive price, so we purchased it from there.

I didn’t want a battery powered sprayer (more to go wrong) and although there would be no way my wife could handle a sprayer filled with 15 L of herbicide, it could be filled to a level she could manage. When I was using it, I’d fill it to 15 L. Talking from experience though, doing up your shoelace is not something I’d recommend with a full load of herbicide strapped to your back.

The model we went with was the Solo 475. It has the diaphragm pump with a maximum pressure output of 60 psi. Typically, you can pick these up for around AUD295.

Post #0058 - Photo No. 1.jpg
The Solo 425 has the piston pump with a maximum pressure output of 90 psi. The piston pump can be damaged by herbicides/dyes that have a tendency to crystalise. This leads to premature wear on the pump’s cylinder. I figured we’d use marker dyes, so the 475 would suit us better.

Post #0058 - Photo No. 2.jpg
When fitting the crank handle, I found that when slipped onto the horizontal shaft as far as it would go, the bolt hole in the crank handle wouldn’t line up with the bolt hole in the horizontal shaft. So, you couldn’t fit the bolt, nut and washer that joined the two together. What it required was some taps on the end of the shaft with a hammer to slide it into the right position where all the holes aligned.

One of the annoying problems with this sprayer are the shoulder straps’ bottom plastic buckles. Firstly, they have a tendency to move along the support frame when taking the sprayer off. The problem is that when placing it on a solid surface, they end up preventing the frame from sitting flat on the solid surface.

Post #0058 Photo No. 3.jpg

Secondly, if they’re left like that when filling the sprayer, the sprayer becomes unstable and you run the risk of spilling the contents you’re discharging into the tank. This isn’t a problem when you’re filling from a hose but definitely when you’re juggling a heavy jerry can.

Then, when you go to put the sprayer on, you’ve got to slide the buckles back, if you haven’t already done that. You need to do this to open-up the loop of the straps, as much as possible to get each of your arms through its corresponding shoulder strap. Secondly, if you don’t do that and manage to get the sprayer on, the whole unit is not balanced.

The handle has a built-in clasp for securing the wand when storing the sprayer. This is really useful, and I didn’t realise it had this until I read the product’s literature.

Post #0058 Photo No. 4.jpg

After completing a fair amount of spraying I quickly realised that intensive efforts, like spraying twice per day over three days was just too demanding and simply wasn’t enough to blitz all the areas we wanted to do. I also found that my left trapezius muscle would be very tight and sore after a couple of spraying sessions.

We headed back to the local hardware and produce store and they were now stocking the Silvan range of sprayers. This time we picked up this ProGrade sprayer for about $190, so it was significantly cheaper than the Solo 475.

Post #0058 - Photo No. 5.png
The key features I liked about the Silvan sprayer were that the shoulder straps’ bottom buckles were simply fabric and they stayed in position and, secondly it had a waist strap. I’m not sure whether it’s just the latter feature but my shoulder doesn’t get sore. Maybe the centre of gravity of the sprayer is just slightly lower than that of the Solo 475.

Post #0058 - Photo No. 6.jpg

Post #0058 - Photo No. 7.jpg

Both sprayers feature a locking mechanism on the trigger. I rarely use this, as I’m mainly spot spraying and just want to release the herbicide in short bursts.

Solo 475 Summary

Pros:
  • Lifting handle.
  • Handle features a clasp for storing wand.
  • Rebuildable/serviceable.
  • Easy to read fill levels on tank.
Cons:
  • Cost.
  • Only two nozzles supplied as standard.
  • No waist strap/belt.
  • Bottom shoulder strap buckles get caught under the support frame causing instability when not being used.
  • In-line filters clogs when using marker dyes.
  • Nozzles can leak when sprayer is stored (it’s recommended to flush the sprayer after use).
Silvan ProGrade 190550 Summary

Pros:
  • Lower cost.
  • Lifting handle.
  • Handle features a clasp for storing wand.
  • Four nozzles included as standard.
  • Waist strap/belt helps with stability, reducing fatigue.
  • Bottom shoulder strap buckles don’t cause instability when not be used.
  • Rebuildable/serviceable.
  • Easy to read fill levels on tank.
Cons:
  • In-line filters clogs when using marker dyes.
  • Nozzles can leak when sprayer is stored (it’s recommended to flush the sprayer after use).
 
Last edited:
OP
K

kitdoctor

Well-known member
Joined
Oct 30, 2010
Messages
531
Location
Sunshine Coast, Australia
Post #0059a - Construction work continues - Plywood lining of garage storage room - Part LIV

With a project like this, you’re always planning ahead, not only the build aspect but what needs to be organised and done around the property.

With the mowing cost running at AUD500 per visit, I thought that finishing the smaller garage should be made a priority. That way, we could arrange for the delivery of our compact tractor and have somewhere to store it. We’d then be able to do the mowing ourselves…

The major tasks that needed to be completed were the internal lining of the storage room and the lining of the outside face of the wall that divides the vehicle parking area from the storage room. I chose plywood for lining both, to allow for easily attaching storage hooks, racks, solar PV equipment etc.

I decided upon Grade AB plywood which has an A-grade face (a smooth, flawless visible side) and a B-grade back (a less-smooth side with minor imperfections like small knots or patches).

It’s a high-quality option suitable for projects where one side will be highly visible, such as cabinetry, displays, or furniture, while the less-perfect back is still structurally sound. It looks beautiful but is expensive. Here’s what a AUD19000 pile of 122 sheets looks like.

Post #0059a - Photo No. 1.jpg

To get ready for installing the lining, a door frame was installed and the outside wall face had the Solitex Extasana Class 4 vapour barrier and ATI Cavibreak thermal break strips applied.

Post #0059a - Photo No. 2.jpg

The door frames are solid Merbau , not featuring any glued or nailed pieces, with a single rebate, rather than a double rebate. I’ll go into more detail why I chose a single rebate when I post about the steel doors used at the shed.

Post #0059a - Photo No. 3.jpg

A small detail that had to be dealt with was how to make the bottom edge of walls that face into the shed and vehicle storage area of the garage water resistant. This was done by fixing an aluminium angle to the concrete slab with silicon (photo is at the shed but the same detail was used at the garage).

Post #0059a - Photo No. 4.jpg

Before installing the lining any gaps were sealed with expanding foam. The objective here is to keep vermin out of the storage room, although it also helps with air-tightness.

Post #0059a - Photo No. 5.jpg

Another detail was how to achieve a neat finish where the plywood lining met the concrete slab. To do this, JamesHardie Edge Base Trim was used. This product is typically used on the exterior, vertical edge of concrete slabs.

Post #0059a - Photo No. 6.jpg

The join between ceiling sheets and walls sheets was something I’d slept on for many months, hoping the subconscious mind would provide a solution. It delivered just in time. The solution was to install a U-shaped, black powder coated aluminium trim in an inverted position to create a shadow line around the perimeter of the ceiling.

Post #0059a - Photo No. 7.jpg

Post #0059a - Photo No. 8.jpg

I was tossing up whether to have a concealed fixing system for the sheets themselves but in the end, I went with a visible fixing system. My thinking was this aligned better with the utilitarian nature of the spaces. More on the installation challenges of installing plywood sheets in a future post.

Post #0059a - Photo No. 9.jpg

In the next post, I’ll include some photographs showing the sheets being installed and the end results.
 

Lyndon

Well-known member
Joined
Aug 11, 2014
Messages
2,535
Location
Sydney, Australia
Post #0059a - Construction work continues - Plywood lining of garage storage room - Part LIV

...Snip

I decided upon Grade AB plywood which has an A-grade face (a smooth, flawless visible side) and a B-grade back (a less-smooth side with minor imperfections like small knots or patches).

It’s a high-quality option suitable for projects where one side will be highly visible, such as cabinetry, displays, or furniture, while the less-perfect back is still structurally sound. It looks beautiful but is expensive. Here’s what a AUD19000 pile of 122 sheets looks like.

Post #0059a - Photo No. 1.jpg

Joel

Is that really $19,000???? Crikey - I was thinking of lining one internal wall of my new workshop in ply - but not at that cost!

I nearly choked on my breakfast toast when I read that... Please tell me it's a typo.

Lyndon
 

Geoff289

Well-known member
Joined
Nov 10, 2013
Messages
1,235
Location
Melbourne, Australia
Joel

Is that really $19,000???? Crikey - I was thinking of lining one internal wall of my new workshop in ply - but not at that cost!

I nearly choked on my breakfast toast when I read that... Please tell me it's a typo.

Lyndon
There's 122 sheets there so $19K makes it $156 per sheet. I'm guessing they're 3600 x 1200. Doesn't seem inordinate for A grade face material.
 
OP
K

kitdoctor

Well-known member
Joined
Oct 30, 2010
Messages
531
Location
Sunshine Coast, Australia
Joel, my heart goes out to you and all the GJ Aussies I consider friends today. Your former place on Bondi Beach has been forever marked by unimaginable tragedy. I am thinking of you but my invisible friend has nothing to say.
@Bob Heine thank you for those kind words.

I think there would be many Australians who would have thought such a terrible event was somewhat inevitable, I know I did. Under the cloud of conflicts occurring overseas there have been a rising number of attacks on both the Jewish and Muslim communities. One thing is certain, Australia is now a different place. Sadly, this is a situation our country has drifted into.

On a day-to-day level we all witness the rising displays of entitlement, selfishness, arrogance and intolerance. Whether it is poor driving, people pushing into queues, abuse directed at retail staff, teachers and the police, vandalism, petty theft, abuse/hate speech on social media – the list is unfortunately endless. These all reflect a decline in caring, restraint, tolerance, trust and shared responsibly.

Our rural community is not totally without its own problems, symptomatic of the gradual breakdown of society, order, lack of social cohesion etc. Bad driving and vandalism are frequent topics of discussion on the local Facebook page. The other day I read about an incident where someone stole the entire contents of a roadside fruit stall including the baskets. Let’s face it, this is deliberate, so it irks me, for example, when parents condone or justify youth vandalism claiming the lack of activities for youth are the cause. They don’t talk about responsibilities.

However, don’t get me wrong, I do feel better that we live in a smaller, rural community. Down on the coast the pace is faster, busier, more crowded and more disconnected. Here it is slower, less harsh, softer, people are more caring and there is a greater sense of community.

Over the last week my wife and I have enjoyed attending two Xmas street parties, one in the street where we are building and the other at a house sit we’re doing. The one in our street is held yearly and the other was a first. At these, news is exchanged, experiences shared, offers of help are extended and plans are made. So, they serve an important purpose, to build and strengthen connections. They show we can all make a difference.
 

Mr onetwo

Well-known member
Joined
Apr 6, 2011
Messages
2,010
Location
Coastal Maine
@Bob Heine thank you for those kind words.

I think there would be many Australians who would have thought such a terrible event was somewhat inevitable, I know I did. Under the cloud of conflicts occurring overseas there have been a rising number of attacks on both the Jewish and Muslim communities. One thing is certain, Australia is now a different place. Sadly, this is a situation our country has drifted into.

On a day-to-day level we all witness the rising displays of entitlement, selfishness, arrogance and intolerance. Whether it is poor driving, people pushing into queues, abuse directed at retail staff, teachers and the police, vandalism, petty theft, abuse/hate speech on social media – the list is unfortunately endless. These all reflect a decline in caring, restraint, tolerance, trust and shared responsibly.

Our rural community is not totally without its own problems, symptomatic of the gradual breakdown of society, order, lack of social cohesion etc. Bad driving and vandalism are frequent topics of discussion on the local Facebook page. The other day I read about an incident where someone stole the entire contents of a roadside fruit stall including the baskets. Let’s face it, this is deliberate, so it irks me, for example, when parents condone or justify youth vandalism claiming the lack of activities for youth are the cause. They don’t talk about responsibilities.

However, don’t get me wrong, I do feel better that we live in a smaller, rural community. Down on the coast the pace is faster, busier, more crowded and more disconnected. Here it is slower, less harsh, softer, people are more caring and there is a greater sense of community.

Over the last week my wife and I have enjoyed attending two Xmas street parties, one in the street where we are building and the other at a house sit we’re doing. The one in our street is held yearly and the other was a first. At these, news is exchanged, experiences shared, offers of help are extended and plans are made. So, they serve an important purpose, to build and strengthen connections. They show we can all make a difference.
Well said mate. 👏
 
OP
K

kitdoctor

Well-known member
Joined
Oct 30, 2010
Messages
531
Location
Sunshine Coast, Australia
Post #0059b - Construction work continues - Plywood lining of garage storage room continued - Part LIV

Hi everyone, welcome back. This post is short, let’s get into it.

In this next photo you can see that trestles were needed to deal with the 3.6 m (12’) ceiling height. The symmetry of the layout of the ceiling sheets can also be seen, with one full sheet either side of the centreline of the room, and one partial sheet of equal width on each side to fill the remaining gap.

Post #0059b - Photo No. 1.jpg

Post #0059b - Photo No. 2.jpg

Here’s a close-up photo of what the JamesHardie Edge Base Trim looks like when finished.

Post #0059b - Photo No. 3.jpg

In this next photo the lining of the storage is complete. Although not visible, the gap between the wall sheets and the door frame was filled with expanding foam. An architrave will be installed around the door frame at a later stage.

Post #0059b - Photo No. 4.jpg

Here’s the completed outside wall face. Again, an architrave will be fitted at a later stage, as well as the door.

What these photos don’t show and you can only appreciate when present is the precise setting out of all the screw fixings which align in both the horizontal and vertical directions. Well done Charlie and co!

Post #0059b - Photo No. 5.jpg

Post #0059b - Photo No. 6.jpg

To complete the garage to the point where it could be used required some electrical items to be fitted off and have the controllers and electricity isolation switches installed on the vehicle access doors.

Although the latter was within the work scope of the shed contractor, I decided to organise this work, so that I would have better certainty over the timing of it being done.

I also organised the contractor undertaking the epoxy floor to start at the garage and complete the floor at the shed at a later date.
 

Mr onetwo

Well-known member
Joined
Apr 6, 2011
Messages
2,010
Location
Coastal Maine
Looks great with the plywood...well done.The base works well...wish it was available here.As with many cool building products we in America are SOL. Merry Christmas to you🎄
 
OP
K

kitdoctor

Well-known member
Joined
Oct 30, 2010
Messages
531
Location
Sunshine Coast, Australia
To avoid these ads, REGISTER NOW!
Top Bottom