Just took my next step in home tooling!

[nahuebsch82]

Might not be huge to some but for me having a compressor at home is a huge next step

Pretty good deal I think at $80.00=>

[URL=http://s7.photobucket.com/user/afguy2082/media/IMAG0143_zpse62a56df.jpg.html] [/URL]

[URL=http://s7.photobucket.com/user/afguy2082/media/IMAG0144_zps994c58c8.jpg.html] [/URL]

[URL=http://s7.photobucket.com/user/afguy2082/media/IMAG0145_zps65d6bceb.jpg.html] [/URL]

 

[TAMPAGT07]

A compressor at home is a must....Good find....Later down the road if your needs change, you could sell it and upgrade..You can't go wrong for $80...

 

[nahuebsch82]

That's what I figured, had to "OK" with the misses but she was all for it. I am having a little trouble finding info on it, I know it's a Grainger brand but the model number doesn't come up

 

[TwoInch]

good deal!

id like to see the rated SCFM number on that unit, being a claimed 2hp.

how many gallons?

 

[Jack Olsen]

That looks like a good deal.

As a side note, and because I'm funny this way, 'tooling' (as a noun), usually wouldn't be used to describe hand tools, power tools or something like an air compressor -- even though they are all tools.

'Tooling' is usually used to describe items used in a specific manufacturing process -- like cutting tools, dies, jigs or fixtures.

 

[nahuebsch82]

good deal!

id like to see the rated SCFM number on that unit, being a claimed 2hp.

how many gallons?

20 Gallon tank....I'd lie to see the rating too but no info online...I contacted grainger for a owners manual so we'll see what comes of that.

 

[nahuebsch82]

Best I could find:

Speed Air Compressor, single Stage Compressor
Model 5Z034A
Max. Pressure 125 PSI
Air Displacement -5 CFM @ 100 PSI
Air Delivery 5.5 CFM @ 100 PSI
Motor 2HP 120 Volts, 15 Amp
Speed 1700 RPM
20 Gallon Tank
This compressor will run over 27 Air Tools ( See pictures)
Compressor Made in the US, NOT A CHINESE PRODUCT.

 

[BK13]

Nice, I would have probably sprained my shoulder reaching for my wallet...

 

[nahuebsch82]

I am not too keen on CFM and what your tools demands are, so here's another question my most demanding tool I think is my die grinder that Requires 4 CFM at 90 PSI would this handle it ok? (tool is at work)

 

[TJJP77]

I believe those were made for Grainger by Campbell Hausfeld. I'm not a huge fan of direct-drive, but at least it is oil-lubed (or at least it appears to be).

 

[nahuebsch82]

I believe those were made for Grainger by Campbell Hausfeld. I'm not a huge fan of direct-drive, but at least it is oil-lubed (or at least it appears to be).

Yeah it is oiled....not quite sure where to fill as of yet but it does appear to have sufficient amount

 

[sberry]

Your die grinder uses about 12 cfm

 

[devoncoolman]

Nice little compressor $80 is a good price.

 

[doan]

I am not too keen on CFM and what your tools demands are, so here's another question my most demanding tool I think is my die grinder that Requires 4 CFM at 90 PSI would this handle it ok? (tool is at work)

Your grinder is likely rated at AVERAGE CFM = 4

AVERAGE assumes 25% duty cycle which is fine for stuff like impact guns, but for a grinder that really means 16. My 80 Gal compressor is rated at about 12 CFM and just barely keeps up with a die grinder or sander.

 

[ZRX61]

My 80 Gal compressor is rated at about 12 CFM and just barely keeps up with a die grinder or sander.

Ditto for my 60gal

 

[jakemac]

I am not too keen on CFM and what your tools demands are, so here's another question my most demanding tool I think is my die grinder that Requires 4 CFM at 90 PSI would this handle it ok? (tool is at work)

My compressor is rated at 5.3 CFM with a 1.5hp motor and 12gal tank. A die grinder will run off your compressor, but it will be a "work - waaaaiiiiiiit - work - waaaaiiiiiiit" situation, with the motor running constantly. Make sure that you have it plugged into a dedicated 20a circuit that is as close to your breaker box as possible. Otherwise you will spend all your time running over to reset the breaker when it trips. (experience talking)

 

[TwoInch]

Your grinder is likely rated at AVERAGE CFM = 4

AVERAGE assumes 25% duty cycle which is fine for stuff like impact guns, but for a grinder that really means 16. My 80 Gal compressor is rated at about 12 CFM and just barely keeps up with a die grinder or sander.

another problem that most dont realize, is that even if the compressor could make the required air volume, the compressor has a duty cycle also. usually 50% on homeowner grade machines.

your compressor makes 12SCFM at 90psi, but you can only run it for 5 out of every 10 minutes...

fwiw, most die grinders are consuming more on the order or 25-30 cfm at load.

 

[CNGsaves]

That's a great 1st compressor (ie mobile and runs on 120 volt) that you will get a lot of use.

However, now you need to watch CL like a hawk for 60 or 80 gallon oil-splash 2 stage air compressor with either 5 HP or 7.5 HP 240 volt motor. Then you'll have the copper vs blackpipe steel question for your airline system, etc, etc, etc.

You're now on the slippery slope to full-blown GJ garage FULL of goodies!!

 

[Drew_flux]

looking good. having a compressor at home makes a big difference. now see if you can find an auxiliary air tank to run in line with your new toy.

 

[nahuebsch82]

Just got the owners manual for the compressor from Grainger::

Max Pressure:.....125 PSI
Air Displacement:.9.5 CFM @ 100 PSI
Air Delivery:........5.5 CFM @ 100 PSI
Motor:...............2 HP 120V 15 amp
Speed:..............1700 rpm

 

[helterskelter]

That looks like a good deal.

As a side note, and because I'm funny this way, 'tooling' (as a noun), usually wouldn't be used to describe hand tools, power tools or something like an air compressor -- even though they are all tools.

'Tooling' is usually used to describe items used in a specific manufacturing process -- like cutting tools, dies, jigs or fixtures.

I agree with this (I work in a machine shop). I'm also surprised Jack is well versed on tooling. I thought you were a writer?

 

[Jack Olsen]

I am. But my father was/is an engineer and spent a lot of years working with guys in machine shops.

 

[nahuebsch82]

Question, I know this is an older thread but is there a way to figure out the duty cycle of my compressor? Obviously its the one stated in the OP. Nothing stated in the Oners manual. I assume it's 50% as I have read most "hobbyist" compressors seem to be. Though, if theirs a way of figuring it out?

Sent from my ADR6425LVW using Tapatalk 2