Recent content by 92nsx

Do you have a Menards in your area? Are you a DIY'er? Total project on mine was under $700. They also have a 45k btu. However for $50 more I'd go with the 75k. Mounts to the ceiling, up and out of the way...

https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F331964637942 Shipping was 2 days! Come out of a warehouse in Ky.

^^^^ It is what I would do. But Im no expert. Lets say you have a 1" hammer drill concrete bit that is say 24" or so long. Drill a hole as deep as you can go and put 3/4" PVC pipe with holes on the bottom side in to the hole you just drilled . Be a tight fit IIRC it is pvc 1.050". Or even...

Just a Idea. Core drill a hole, or hammer chisel a hole in the concrete. Dig a hole into the earth as deep as you can go. Put a PVC pipe with holes all round/ over it. Put pipe in the hole. Put a metal grate over it. Let it drain in there. 3-5 gallons a day the ground should absorb it...

Well I figured I would give them a few months of testing before I posted. I have to say so far so good! Zero failed. :rocker: Garage size 45' deep 22' wide 12' ceiling Well we all know how expensive lighting a garage can be. I couldn't find a install review on them. So I pulled the trigger...

Personally I like the 75K's. When I want heat I want heat. I use Menards beacon Morris units. Only $50 difference between 45 and 75k. I have them in both attached garage (22x22 with 9 foot ceiling) Insulation is "so so". Ceiling and only 2 walls insulated, and detached garage (22x45 with...

Get a Fireboy CMD5 Marine CO detector and wire it up to 12 VDC. My new one (thanks to MN law) will go off wile idling down the no wake zone or warming up the engines at the marina in my boat :eyecrazy:. When my digital battery one will read 0. Kind of a PITA, but I guess i know it works.

When I looked into them....... Con. One very big one. VERY EXPENSIVE!!! Pay back on them Vs running NG 75k garage heater.. 2 life times. And that is saying you and your buddies have enough oil to feed it all winter long. If you have to buy waste oil..... Last I heard around here it goes...

Yes. They are open/closed. Normally is has to be in the closed state. Can "test" by jumping the 2 wires together. Roll out switch shuts down unit when is gets HOT, like open flame and over time. Opens the contacts. Some you can reset with push button, some are just one time use

Roll out switch is bad, unless you have a hole in your tube letting flames out. Go to youtube and type in roll out switch. Easy to replace 2 Phillips screws and 2 push on wire connectors.

We rollered it. Just plain old OSB no prep and flat maintenance white paint. Once again its a garage not a show room. It took 20 gallons for my Garage. 3 coats to cover. (it could use another coat but Im sick of painting.

You just have to make sure you have the "C" (common wire) for power and your good to go. All of the units will have it, just some don't terminate it to the exterior of the unit. To 1 up the programmable.. Wifi. Program it infinity ways and smart phone accessible.

$338 total:thumbup::thumbup::thumbup:. 4 runs with 10 tubes on each run. Plus still have 10 extra 4' LED tubes. (will turn them into wall / detailing lights). They come in pkg of 25 for $169. T8 led integrated LED tube. Each tube is 20 or 22 watts I have short term memory, lol. There 6k...

All said and done with lights. Material cost to get wire to the garage, wire it and light it (22X45) was $1103. Every thing is rigid conduit, quad outlet every 10' along the walls. (dose not include the cost of heat) No 220 outlets yet..... Not sure where I want them yet. Go romex and...

Being in woodworking you wont like the direct vent heaters. It will blow saw dust all over. You will prob want a infrared heater. Something like this. https://minneapolis.craigslist.org/dak/tls/d/garage-heater/6355649160.html How ever the 75k Beacon Morris direct vent heater you can pick up...