Recent content by Cameronlunz12

  1. C

    I beam load capacity

    I did buy it, it’s in good shape for the price of it. It ended up being 18’ long of usable length instead of 20 which isn’t a big deal. But before I start on this project I need to make mounts on my loader so I can mount it to my tractor. (Because that’s the only way I can get the legs for the...
  2. C

    I beam load capacity

    The supports that I’m using are 20’ long, but after I sink them in the ground and concrete them the bottom of the I beam will probably sit around 13’-14’. But I haven’t bought it yet, the guy only wants $100 for it and the exact dimensions he told me was 12” tall, 10” wide, and 1/2” thick. By...
  3. C

    I beam load capacity

    I’m building a gantry crane next to my barn and I can’t seem to find much information on center load capacity for I beam. I have some really heavy box beam and c channel I’m using for my supports that I got for free and have a chance to buy a 20’ section of I beam that is 12”tall by 10” wide...
  4. C

    Ingersoll rand t30 wiring

    The last of the pictures I took
  5. C

    Ingersoll rand t30 wiring

    I pulled the box of the motor to see where the individual wires go. I see the blue and black wire coming from the pressure switch are both power wires, and the motor must get its ground through the tank. I’m assuming the thicker white wires going into the motor are both power wires, and all the...
  6. C

    Ingersoll rand t30 wiring

    It might have been replaced at some point, but not since I’ve owned it. But not that I know of there’s no reset button or anything on the motor
  7. C

    Ingersoll rand t30 wiring

    Okay. The blue wire goes to the pressure switch. There was no cover when I got it, but anything I find online for new motors that match the model Number doesn’t have the switch on the cover. I wil get that conduit pulled off later to get a better view to trace the wires
  8. C

    Ingersoll rand t30 wiring

    Yeah I’m gonna replace it once I get the wiring figured out and see if it does it again and go from there
  9. C

    Ingersoll rand t30 wiring

    Okay so the longer white wire with the black insulated flag connector goes to the two capacitors that are wired parallel, and the short white wire with the connector goes to the white capacitor and the blue wire into the wire nut? But then that leaves the longer wire with the tab connector and...
  10. C

    Ingersoll rand t30 wiring

    That’s all I’ve got
  11. C

    Ingersoll rand t30 wiring

    I have an ingersoll rand t30 air compressor with a single phase weg 00518os1ccd184t electric motor on it. I ordered a new motor start capacitor and when I moved the air compressor to my house the wires running from the 3 capacitors disconnected from each capacitor and the wires going to the...
  12. C

    Single phase to 3 phase

    Okay, where can I message you at? Also I got some more pictures today that are clear.
  13. C

    Single phase to 3 phase

    So as long as I wire the VFD in between the plug and the machine it should work fine? And if I run it at 60hz it won’t mess with the computer at all? Also I can get more pictures of the computer board and cut that ziptie if you still want them.
  14. C

    Single phase to 3 phase

    The blue line is the power from the wall to the computer and the green one is from the computer to the motor. So would I be able to just wire the vfd in between the computer and the motor, and then change the plug so it’ll plug into single phase 220? Or is there more to it
  15. C

    Single phase to 3 phase

    Okay, I’d be fine with the 1hp VFD, but would it work with the computer? Or would I just need to wire it in, in between the power supply and the motor itself. Or would the vfd power both the computer and the motor? Here are the pictures of the computer.
See more
Top Bottom