Recent content by CVPIJoe

I have looked on here but have not seen what I am looking for. I have a bout a dozen wheels/tires and would like to get them off the ground. I Most of 17-18" But I do have a spare set of 22" for my truck. I have 12' of space that I want to build a tire rack on the wall. My question is, what...

I get what you are saying now. Had a big DUH moment after reading your reply 5 times. That makes complete sense now and the 20 min it will take to take the cables apart will save me hours of scratching my head trying to figure out how to tighten those bolts. Thank you for the help again!!! :beer:

That certainly makes sense with the arm stop. Explains why I cannot use it and explains the purpose of it. I did intentionally put the pump side on the driver. Thank you ! My issue with the lower cable nut is not being able to get anything in there to tighten it down. My only thought was to...

Hoping you can help ! Can you tell me where the arm stop is at on your lift ? Also how the hell do you tighten the cable nylon nut that goes on the bottoms of the carriage ? Thank you !!

I do have a finish nailer I can borrow from my neighbor :lol_hitti They built our house as well, the garage they didn't seem to include a lot of finish things on because they just see it as a garage. They told me if I did drywall on the walls they would have finished it like normal but not...

Good info. Thanks !

Thanks everyone. I am going to go forward with putting up trim. Now I have to figure out how to since I have never done it before :lol_hitti Our house has "craftsman" style trim on the windows which is just plain square which I like. Do you have an example of how this would look? forgive my...

I resell them. some Police departments and fire departments don't have big budgets so they will buy used. I also changed colors out to amber or green for others to use for anything else.

So garage has OSB walls and drywall ceiling. The builder does not install trim and the gap between the drywall and OSB is pretty big. (1.5") Two things Should I put trim up around the top of the garage to try and hide this gap? If so what it best to use? Also, Should I bother with...

Awesome !! I bought one myself in December and I am anxious to get it into my new shop and setup. I jumped on it because the other one they had I wanted jumped in price $100. I did double check your link and it is still showing $3099. I am looking forward to using it. Let me know how you like...

Photos I posted of painting earlier were of the Primer. 3 coats of kilz oil based primer. about 13 gallons used This photo shows the bottom half painted with the top coat which brightened it up quite a bit <a href="https://ibb.co/C7vZgHv"><img src="https://i.ibb.co/Z8KP5MK/IMG-1760-1.jpg"...

Hello! Where at?!! Thanks Honestly this is what the builder recommended. All I know about it is it is an 80% efficiency Lennox unit. It was originally a 96% but the contractor recommended we change it since the 96% had the possibility of freezing being outdoors.

Been a little while since I posted. I painted the walls and the HVAC was installed. <a href="https://ibb.co/bvCCT3t"><img src="https://i.ibb.co/rpzzYt9/garage1.jpg" alt="garage1" border="0"></a> <a href="https://ibb.co/VL6BRVd"><img src="https://i.ibb.co/3TKh21w/garage2.jpg" alt="garage2"...

Thanks everyone for the feedback. I am working with AquaMoose to get this squared away since I realize now that this may be a much bigger job then I had originally thought

Hey guys I have to create about 40 wiring harnesses and its a total of about 1600 terminals total. What is the best and most efficient way to do this? <a href="https://ibb.co/sRD3B8Y"><img src="https://i.ibb.co/1Qp2SFW/Capture.png" alt="Capture" border="0"></a> Hopefully you can tell by the...