Recent content by N Heat

  1. N

    ok wood stove people

    Dryer lint
  2. N

    Would you take this table saw for free?

    http://www.tools-plus.com/delta-36-t30.html That saw would be really nice with this fence. I put one on an old Craftsman saw. You would have the ability to make some really nice stuff with this setup.
  3. N

    Honda Civic (Acura EL) Timing Belt Replacement

    I did mine on my 01 Civic a few months ago. This tool was the best $16 I have spent. http://www.amazon.com/dp/B0000TMLWQ/?tag=atomicindus08-20 I used a Gates kit from Rock Auto.
  4. N

    Replacing deadbolt that is keyed the same as the knob

    I have to replace a deadbolt lock, and I want to keep it keyed the same as the knob. Is this something that I have to get a locksmith to do, or is there a way I can do it?
  5. N

    Insulating recessed cabinets in knee wall? How to insulate?

    I am planning on installing recessed cabinets in my knee wall above my garage. The room is heated/cooled by HVAC. Currently, the knee wall has insulation bats in it. After installing the boxes, I was going to crawl in behind the knee wall and try to attach bats to the cabinets. Any other...
  6. N

    Artillery Fungus

    I'm a power washing contractor, and I usually tell people it's not worth the effort to remove it. On vinyl, you can use a Mr. Clean Magic Eraser on each individual spot, and still possible leave a shadow.
  7. N

    Removing paint from deck, help!

    Im a powerwashing contractor. I, personally dont mess with trying to remove paint. High pressure is not for wood. I would either sand it, or replace the boards.
  8. N

    Harbor Freight chainsaw

    A few months ago, I saw a chain saw in a Harbor Freight ad. All I can find on their website is a Poulan, which I don't want. Is anyone familiar with the other one they sell? I know their small engines have pretty decent reviews, so I figured the chainsaw might be worth a look. It would only...
  9. N

    Calling All You "Uber-Neat" 2 Car Garage Owners

    This is gonna be my next project. 8x20 loft over the garage door. Luckily, my ceiling is almost 14' tall. http://www.garagestorageloftbuilders.com/PC120149.JPG
  10. N

    Drilling holes for new deadbolts

    Thanks for the help guys!
  11. N

    Drilling holes for new deadbolts

    I need to drill holes for deadbolts. I've seen the cheap DeWalt and Irwin kits at the BORGs, but I'm a little afraid them being made of plastic. http://www.lowes.com/lowes/lkn?action=productDetail&productId=132990-70-D180004&detail=cr&lpage=none Anyone have any tricks to help with this, or do...
  12. N

    Ridiculous deal on Hitachi framing nailer

    Some manufacturers are now making a full head nail for 28-34 degree nailers. Paslode, for example, has a "Round Drive" nail where the head is offset on the shank. They can be shot through a 34 degree clipped head nailer.
  13. N

    Ridiculous deal on Hitachi framing nailer

    They have a steal on the the AE also at $140. Free shipping on both of these also. I put my email address in to be notified when they get more in stock, and hopefully all details will be the same.
  14. N

    Ridiculous deal on Hitachi framing nailer

    I was browsing the net looking at Hitachi compressors and and came across this deal. . http://www.reconditionedsales.com/Hitachi_NR90AD_3-12_Clipped_Head_Framing_Nailer___i1157.aspx I hope it's not too good to be true.
  15. N

    Insulating a water heater in the garage

    My water heater is located in my attached garage. Most of the time, I keep the man door open for my dogs to go in and out. Now that the weather is cooler, I'm more worried about heat loss. What can I do to insulate my water heater? Can I just wrap it with fiberglass insulation, or would a...
Top Bottom