Terrick down Under's latest activity
-
TTerrick down Under reacted to Ford52PU's post in the thread Between 485 & 705 SQ/FT My Garage, My Truck and the Spit! with
Love.
A Unexpected Twist has arisen. After my truck adventure we had an anniversary trip planned for Chincoteague Va. we’ve been going there... -
TTerrick down Under reacted to Vieux's post in the thread Below 265 SQ/FT Very small garage in Russia with Sad.
It's been a long time since I've written anything. The tractor project is moving very slowly. There is still no mobile internet in the...
-
TTerrick down Under replied to the thread Between 265 & 485 SQ/FT CNCs and Hot Rods, a Sydney Garage.yes, corn cob is a generic term for them, schruppen frasser is the german ones we used at the Royal Australian Mint (1985-1993) on the...
-
TTerrick down Under replied to the thread Between 265 & 485 SQ/FT CNCs and Hot Rods, a Sydney Garage.hey, look up "Shrupenfrasser" end mills, I used to use them on the cnc mills back in the early 90's, very clean rapid removal with very...
-
TTerrick down Under reacted to strength_and_power's post in the thread Above 1200 Sq/FT Finally getting a seat at the grown up table with Like.
More progress on the mezzanine. Focused on the 10’x20’ section. Got all the I-beams in, including framing out for a dumbwaiter which...
-
TTerrick down Under reacted to hardtop5000's post in the thread Aussie Earthshelter and Garage with Like.
It was a beautiful day at the racecourse and the lineup of cars on the grass was great. It reminded me a bit of when the ASRF Nationals...
-
TTerrick down Under reacted to Beelzeboss's post in the thread Between 265 & 485 SQ/FT CNCs and Hot Rods, a Sydney Garage with Like.
I think I have the CNC back to being useful, I cut the remaining clamp down holes out to 10.2mm Thread milling the M12 threads was...
-
TTerrick down Under replied to the thread Aussie Earthshelter and Garage.Are they ever finished? Had to lift the bed to fit a trunk floor to stow away stuff like spare wheel, tools, jack and fuel can. Took a...
-
-
TTerrick down Under reacted to Beelzeboss's post in the thread Between 265 & 485 SQ/FT CNCs and Hot Rods, a Sydney Garage with Like.
These should help with the flex in the mount. It's still only 2mm wall where the ballscrew attaches but it's a very short distance to...
-
TTerrick down Under reacted to BB767's post in the thread Above 1200 Sq/FT Restored 1930's Auto Shop with Love.
Sharp eye Bob, yes that's my sweetheart enjoying 1st class on a UAL 787, non-stop ORD-HNL. After all those years flying other folks it's...
-
TTerrick down Under reacted to Beelzeboss's post in the thread Between 265 & 485 SQ/FT CNCs and Hot Rods, a Sydney Garage with Like.
😅 :LOL: Thanks mate, unfortunately I don't have a fly cutter but I've ordered a 35mm diameter face mill which should do the trick. The...
-
TTerrick down Under reacted to Ralf99's post in the thread Below 265 SQ/FT Hewey's 1950s single garage & cottage with Like.
Pretty sure they were indeed assembled from AMC kits by AMI in Port Melbourne, in a factory that later formed part of the Toyota plant...
-
TTerrick down Under reacted to hewey's post in the thread Below 265 SQ/FT Hewey's 1950s single garage & cottage with Like.
This weekend's working bee was relocating an old Jeep. It's a Jeep Gladiator from the early 70s running a 302 Windsor. When I say...
-
TTerrick down Under replied to the thread Aussie Earthshelter and Garage.Thanks, I am pretty happy about it too, I still have a lot to do before checking out of here.
-
TGood to see you back Terrick. That sounds like a pretty rough trot to get through, glad to hear you're on the better side of those odds...
