Show your new tool arrivals
- Thread starter sarel.wagner
- Start date
ElectroMechTech
Well-known member
If your trying to get all the brands Douglas Plumbing tools has those too. First saw them sold under that label before anyone else like 30 years ago. Green handles at the time but otherwise appeared identical.
Last edited:
ElectroMechTech
Well-known member
I've got many private label variants I need to get around to posting.
Attachments
I picked these up the past few months, working on different projects or when something went on clearance.
Bought this crimping tool, when changing out the A/C resistor on our Suburban. Of course GM changed the design on it.
This tool came in handle to crimp the open barrel style connectors. Made for cleaner look, when making your own plug connectors.
Bought this to strip smaller gauge wires for the Suburban A/C resistor replacement.
This a Schrader valve replacement tool. This tool suppose to allow you replace the Schrader valve with out losing the freon. Haven't used it yet.
This tool is a must I feel to remove the rear axle bearing. This puller made short work in removing the bearing on my 1997 C1500.
The 2 pack magnetic tape measure and Milwaukee combo pack rafter and trim square I grabbed at Home Depot.
They were both on clearance for $11. Which I felt was too good to pass up.
Bought this crimping tool, when changing out the A/C resistor on our Suburban. Of course GM changed the design on it.
This tool came in handle to crimp the open barrel style connectors. Made for cleaner look, when making your own plug connectors.
Bought this to strip smaller gauge wires for the Suburban A/C resistor replacement.
This a Schrader valve replacement tool. This tool suppose to allow you replace the Schrader valve with out losing the freon. Haven't used it yet.
This tool is a must I feel to remove the rear axle bearing. This puller made short work in removing the bearing on my 1997 C1500.
The 2 pack magnetic tape measure and Milwaukee combo pack rafter and trim square I grabbed at Home Depot.
They were both on clearance for $11. Which I felt was too good to pass up.
I've seen a lot of those in my feed lately as "sponsored" posts. In other words, ads.
manwithtools
ALLIANCE MEMBER
Koken 1/4" and 3/8" Wobble/Fix extensions. These things fit their ratchets and sockets so well.
Last edited:
Koken in the house again!!!!!!!Koken 1/4" and 3/8" Wobble/Fix extensions. These things fit their ratchets and sockets so well.
Lowlevel2021
Well-known member
- Joined
- Dec 14, 2021
- Messages
- 187
Had to get the 1/4” ratchet as well. Moving the older models to the work truck.
Steel_Rain
Well-known member
- Joined
- Apr 23, 2024
- Messages
- 1,454
ronkz650
Well-known member
I guess no one cares the Koken Wobble-Fix is on wobble 95% of the time with no way to press them on for a straight extension? All Koken bit sockets in hex or torx you are stuck in wobble, all the Zeal standard sockets you are stuck in wobble. They work OK on mid length or deep sockets, otherwise a waste of money and an aggravating experience.
The Fujiya Kurokin is the only new one, but I compared it to the Twingrip 150 and Engineer PZ-58 in a recent video.
I have an older version, but these are also a good comparison to the TwinGrip.
Made in Japan
My first trip to a B&M Northern Tool store yesterday yielded 4 clearanced Diablo wood auger bits, 17.5" long.. 1", 7/8", 3/4" & 5/8". With tax $40.**
Picture later.
Picture later.
manwithtools
ALLIANCE MEMBER
I'm not sure how you reached the conclusion they don't work with other sockets. I just checked them with 40+ year old SK, Snap On and Craftsman. Also fairly new Toptul and Astro Nano's and they work in wobble and fixed mode just fine. Aslo work fine with all my Z series new sockets. I don't have any Koken bit sockets in hex or torx, so I'll have to take your word on those.
Last edited:
Winterborne
Well-known member
- Joined
- Dec 3, 2025
- Messages
- 48
Markoos
Well-known member
Whats in the bag then? Can not just casually mention it and leave at that.Electrician’s shears, protective jaw covers for 10” Cobras, and an 8mm T-handle.
I need to stop before my Veto is 50lbs…
Steel_Rain
Well-known member
- Joined
- Apr 23, 2024
- Messages
- 1,454
Maybe I'm reading what your saying here wrong, but the standard lenght size Koken Zeal sockets work in either fix or wobble just fine with all three drive sizes.
Here they are fixed:
And wobble:
They also work fixed/wobble just fine on the 3/8" locking extensions as well:
These are all standard length Zeal sockets. They also work fixed/wobble with the nut grip sockets in all sizes.
Do you own these? If so, what drive size are you using? Are the sockets you have Zeal?
Steel_Rain
Well-known member
- Joined
- Apr 23, 2024
- Messages
- 1,454
Yes Squanks, even you shite 40 year old Craftsman sockets work
:
I can't get anything not to work. Everything I have at home...Craftsman (new and old), Gearwrench, SK, Dewalt, Milwaukee, Hazet, Vessel, Quinn, Tekton, KTC, SO and Mac all work fixed (and wobble) in standard/deep socket length. This includes all my socket bits from the same brands in hex, XZN, Torx/Torx+, polly and PH/flat.
I don't own any bit sockets from Koken (yet).
manwithtools
ALLIANCE MEMBER
WHAT?
You really need to give them a try. They represent a great value IMHO.
It also makes sense the wobble/fix would work with any sockets. The dimensions of sockets are very standardized.
Steel_Rain
Well-known member
- Joined
- Apr 23, 2024
- Messages
- 1,454
WHAT?
You really need to give them a try. They represent a great value IMHO.
It also makes sense the wobble/fix would work with any sockets. The dimensions of sockets are very standardized.
That's why I love GJ so much. It's like I tell my wife, the guys here always give me suggestions on all these tools that I "NEED".
I will give them a try.
I returned (or sold, can't remember) the Koken 1/4" Wobble/fix extensions that I bought a few years ago because they wouldn't work correctly with some Snap-on deep chrome sockets. The wobble worked, but not the fix - the sockets didn't have enough depth in the drive hole to engage the flats of the "fix" before the tip of the anvil bottomed out in the socket. I think this was the case, anyways. I like dedicated separate regular and wobble extensions at home in the toolbox, but wanted wobble/fix extensions for the travel tool kit to have more options at less weight. I purchased a Snap-on wobble plus extension and it worked.
These same sockets don't sit flush down to the aluminum on the Westling socket trays either, so maybe they're shallower in their drive pocket than what's expected.
---
I got this OMT bearing race driver set a few days ago. It seems well made, but I haven't used it yet.
These same sockets don't sit flush down to the aluminum on the Westling socket trays either, so maybe they're shallower in their drive pocket than what's expected.
---
I got this OMT bearing race driver set a few days ago. It seems well made, but I haven't used it yet.
Last edited:
Stridercondor
Member
Snap on guy got me for these new 7 inch pliers. I have the 10 inch pair and I really like them, so having a smaller pair will come in handy for me as I seem to always be working with one hand a lot.
four.cycle
Well-known member
Did you try any late-production Craftsman "double detent" type sockets?
Snap on guy got me for these new 7 inch pliers. I have the 10 inch pair and I really like them, so having a smaller pair will come in handy for me as I seem to always be working with one hand a lot.
I haven't bought anything from Snap On in over a year, I think my last purchase was the 10" version in April '25 with a few other items.
Anyway... What is the part#? I don't see a smaller version on the website.
Yes Squanks, even you shite 40 year old Craftsman sockets work
Don't you have enough sockets? (Said the guy still using his 1980's Craftsman sockets.)