Show your new tool arrivals

[Jarhead0408]

You guys are killin' it with the Martin stuff!

Thanks.

We try, we try.

Haha.

 

[YesIHaveAHammer]

Klein LAN Scout® Jr. 2 ethernet cable tester VDV526-200
On its own, it verifies the cable and displays the detail of any fault/mistake. It can also generate tones for tracing cables with a separately available probe. The short patch cables were separate, essential for testing installed sockets end to end. The range includes one more basic and two more advanced ones.


Facom 441 XL OGV Grip wrenches 11, 12mm
Filling out more of that partial set I got cheap.


Facom 41 Offset Combination Wrench 13mm
Just trying something a little different.



Saltus 3=1 swivel socket combination wrench 15mm
Filling a gap in my set. They're rarely available now so I figured it's my only chance.

 

[Monte]

mini pry bar . Blade is about 0.35mm thick.

 

[chohdog]

Have gone a little plier crazy lately.

 

[Jarhead0408]

Have gone a little plier crazy lately.

That little retractable scraper is my favorite out here in the Wide World of Trucking. I use it to scrape off adhesive HazMat placards. It works great. I need to buy a few more in case they ever discontinue them. I wish I knew who the OEM is.

 

[Jarhead0408]

Facom 441 XL OGV Grip wrenches 11, 12mm
Filling out more of that partial set I got cheap.

Everything about Facom wrenches just strikes me as quality. I'm a big fan of them.

 

[craftsman creep]

Had to pick up some new icon stuff while on sale

 

[ETJ]

Used Snap-on EEPV508 transmission and engine pressure set



Unused 2nd hand Blue-point (RIDGID) E1025 extractor set. Only paid 55 euros compared to the silly list price of $1220.


Used Snapon sockets:
- 208EFAY SAE standard hex bit socket set
- 206EFABL SAE long ball hex bit socket set
-206EFAL SAE long hex bit socket set
-206EFAML Metric long hex bit socket set
-Older 9-piece BEXD deep extractor socket set
-Two low profile spark plug sockets



Snap-on SAE line wrench set RXFS605B.
Lisle small hose clamp vise and filter wrench.
Bahco filter wrench.



Snap-on REX25C Multispline screw extractor set and EXD10 screw extractor and drill bit set.



Bahco brake line tools


and couple deburring tools

 

[Markoos]

Phase 1 completed thanks to arrival of this
Which led to this

 

[mikeinri]

Some seriously valuable wisdom here...

It can be best for DIY use to have a USA Vermont American quality level set covering most occasional needs and eventualities and replace specific sizes in that set that you use a lot with higher quality ones. Then you do not break the bank to cover stuff you only use a little, have good coverage for what might come up from time to time, and also have good ones for the sizes that you use a lot.

By the way, some of the people showing tap and die pics should oil + clean them more before storage. When they rust, it degrades the cutting edges. I try to wipe mine down with something like WD-40 after use and then store them somewhere dry. Surface rust will mess up a good quality top or die and it is much easier to prevent than to try and address it or resharpen after it starts rusting. It is also not a good idea to let cutting oil and grime harden into a sludge on them. They usually clean up pretty easily if done right after use.

Mike

 

[Beerhippie]

By the way, some of the people showing tap and die pics should oil + clean them more before storage.

I use lots of cutting oil when I use them. They never rust. I blow the swarf off before putting them away.

 

[PugetDude]

I keep an oily old 1" HF chip brush with my taps and dies to brush them off before putting them away.

 

[rmack898]

The bookstore dropped off a new micron vacuum gauge for installing the two mini splits I bought for the shop

 

[Skyman]

The bookstore dropped off a new micron vacuum gauge for installing the two mini splits I bought for the shop

Please report back with your thoughts about this one after you use it.

 

[rmack898]

Please report back with your thoughts about this one after you use it.

Probably be two weeks before I use it but I'll let you know what I think.

 

[Skyman]

Probably be two weeks before I use it but I'll let you know what I think.

TIA.

 

[gilbo]

I just got my USA made Irwin tap & die set from Menards.





I also got this set of press and pull sleeve. Made pressing in bushings a breeze for my suburban



I also got a couple fluid extractors. The Four Uncles pneumatic/manual makes changing ATF a lot less messy. I just used this week to drop the pan on my OBS C1500, so much quicker and easier, but mainly no mess. If you don't have one get one.



The OMT fluid extractor will be great when changing brake and P/S fluid.

 

[AJHD]

I just got my USA made Irwin tap & die set from Menards.

Was this recent? Have a link and price?
I passed on the Icon sets this weekend at 20% off. Unfortunately actual USA made kits are ceasing to exist and in a hurry.

 

[gilbo]

Was this recent? Have a link and price?
I passed on the Icon sets this weekend at 20% off. Unfortunately actual USA made kits are ceasing to exist and in a hurry.

Yes, just last week

Menards Irwin USA made tap and die