Search results

Wera Zyklops 1/4 drive roto ratchet. Replaces my VIM roto ratchet that broke and they did not have a direct replacement. This is better than the VIM, which I realy liked. My only constructive criticism is that I wish it had a wider handle so you can generate more torque when using it in...

OK. fair enough. The Innova does service resets.

It works with the VW/Audi VAG Com. It will do VAG COM key programing and software changes? If anyone Knows.

I bought the 5610 last Spring for $350 directly from Inova and it came with a free Boreascope valued at $99. Even If I could have bought it alone for $50 I thought it was a good deal. Being a typical GJ member, I thought the Borescope may come in handy for certain situations in the future. I...

I ended up installing Series 10 full view Anderson last Fall. I did not want to deal with the plastic retaining strips that always seem to break after a few years. I wanted the full view over a partial view. I like how easy it is to swap out the glass for the screen and the built in door...

I get it. Very, very, very unlikely I will run all 4 stove burners and the oven at the same time. Currently I have a HWH, furnace, stove and one gas fireplace. Looking to add a 2nd gas fireplace.

Natural gas. Model is I-250. Can I assume it is 250,000 Btu/hr?

I am considering adding another gas appliance. How do I calculate if the current line coming into the house can handle the potential extra demand? I was told there are charts that are based on the main line pipe diameter. It will give you the BTU/Hr total for the house. What is this chart...

Does anyone have direct experience with this PRO sensor Max from Franklin? it claims to sense up to 2.5" deep but costs about twice as much. https://franklinsensors.com/prosensor-max/

I have a Franklin 150 and it works fine on dry wall but not so good on plaster. I have yet to find any stud finder that is reliable on plaster walls. I live in an area with a lot of houses that are 150 years old and older. You can not count on 16 inch center studs or a consistent spacing. If...

I have never used the HF but have used others and I always felt i could go faster and do a better job with my orbital nozzle. they were heavy enough and worked ok by some standards. Depending on your standard of ok.

FWIIW. I just successfully used a spiral EZ- out on a broken off 1/4-20. It was an interference thread type bolt on a small engine(I do not know the official name for those bolts, anyone know?). I bet it was likely over tighten and the head snapped off. I am assuming this, as It was...

I have had some success with a 20 year old Craftsman Bolt Out set . The type you hammer over the fastener and hope it grabs it well enough. Maybe a 33% success rate. When It works you do a happy dance. Otherwise you are drilling. Transfer punches do help you center the drill. I like the...

How do they peel off? cleanly with no residue? Can they be resued or are they one time use and you reprint new labels. I do like the look and flexibility the Brother labels offer. As far as sellers on eBay who fulfil their orders from Amazon. You can often spot them. Not always. They ship...

I know. I just hate to support Amazon. I try to avoid those resellers. So share your better ways, please.

Has anyone found Magnetic tool box labels that they like? I bought some a few years back and the magnet strength is not as good as they should be. They occasionally fall off. I want magnetic because I change things over time and a permanent sticker would be a PITA. There are plenty with...

I looked at that set which is reasonably priced. But they skip the 3/4 which I do use. They also skip the 18mm which I have never had a need for but you never know what the future will bring. Substituting one of the 5/8 sockets for a 3/4 and I would likely pull the trigger. I do not mind the...

This is disconcerting. I knew it was happening on Amazon with things like spark plugs. I had a brand new Toro snow blower that appeared to have a counterfeit Bosch plug in it. Now they have infiltrated the OEM auto companies and parts stores like NAPA!!! What are the Auto companies like...

I know what you mean. It seams nobody any longer takes their flags down at sunset or keeps it lit at night. Not the banks, car dealers or and many municipal buildings. They leave it out. Sometimes they put it at half staff for obvious reasons. Am I getting too old?

I just saw a sizable display of these at my Lowes and I did not think these were not intended for everyday use. I am not a tool novice as many people buying at Box Stores are. Some will be buying gift items purchased by a well meaning son/daughter/wife etc. I suspect there will be a fair...