Search results

Looking for an EZ Car Lift http://www.ezcarlift.com -Scott

Need a 20% coupon code I can use online. Can someone post a current one? Thanks. -Scott

Thanks. If you look at these 2 pics, it's the black thing with an o-ring on it on the end of the silver pipe. It should go in that long vertical black thing, but won't stay in it anymore. -Scott

I've got a Craftsman Professional 80gal compressor. I was grinding some stuff so it was cycling a lot when all of a sudden I hear a large hiss from my compressor closet while the compressor was running. After shutting it off, it stopped hissing. I noticed that the small pipe that goes from...

I'm thinking about getting this set to hang on my pegboard. Can you use the supplied plastic holder to hold the sockets or once you remove them, they don't stay on? -Scott

Make sure you isolate the compressor from the ground. I used 4 hockey pucks under the compresor and that made a huge difference in reducing the noise. You can see what I did to reduce compressor noise here. http://garagejournal.com/forum/showthread.php?p=646376#post646376 -Scott

-Scott

I usually do open the garage door when I work in there, but in the winter its way too cold (currently in the teens). Also when I clean up I usually sweep up, and then use the air hose to blow as much stuff as I can out the door. This usually creates a lot of dust. I would like to use the...

The pads are 24"x24" and 12" deep. 5000psi concrete. I am not the guy who runs Bimmertools.com but I am good friends with Ken who does. I do run MyTrackSchedule.com though. ;) -Scott

Any recommendations for an air filter system to help remove dust and vapors/gases commonly found in garages? Preferably a HEPA with active carbon, not an Ionic or ozone one. Will need to be able to clean 500-1000 sq-feet. -Scott

Also here is a live web cam of my MaxJax lift. -Scott

Here are some pics of my lift in action: Dropping the engine of a friend's Porsche My 24 Hours of LeMons race car I'll try to find a pic with my Yukon XL on it. :rocker: -Scott

I've got this problem too. What did they do? It doesn't seem to be effecting anything right now, but don't want a failure later. -Scott

One of mine fell out too when I got it. Is this bad? I can't figure out how to get it back in. -Scott

Here is what I did when this happened to me. Raise the lift to the max w/o anything on it, then swap hoses, then lower. It will be hard as hell to put the hoses back on. You might have to have someone push the lower button a little as you are trying to put the hose back on. It seemed to fix...

Just an update. I finally got my compressor closet quiet enough to be able to have a normal volume conversation even standing next to it. Here are the steps I took in chronolocial order 1) Anchored the compressor to the concrete with Wej-It type anchors. - Compressor was so loud that even...

Also, the filters I have found have a poly bowl and a rating to 150psi. The outlet on my compressor is 180 psi. Should I just put the filter after the regulator, or should the filter be before the regulator? -Scott

Thanks Charles. So just a filter and regulator will be fine. When you see a line of the devices, filter, regulator, separator. Is it a general filter, regulator, and coalescing filter? -Scott

I haven't found any 3/4" water separators. Most filters I see, look similar to TP tools water separator. Are they the same thing, just called different names, or is a separator different from the filter? TP Tools water separator Parker Air filter Is Parker good? -Scott -Scott

3/4" filter/separator/regulator Loooking for a cheap but good 3/4" filter, water separator, and regulator. Links please. Also do these need to be installed horizontally or can they be installed on a vertical run? -Scott