Search results

I would like a pressure washer reel with 25-50 ft of hose so I can easily go around my vehicle when it is parked in front of the garage bay. These seem to be fairly expensive, I was wondering if anyone had insight on these, or perhaps a different suggestions? for what it's worth, the hose that...

Rinnai direct venter heater ,the exhaust port is tiny. I think it is a 3" or 4" hole. I put an EX38 in my 28x28 spray foamed garage in VT and it is way more than I need. I honestly think I could have gone with the 11k btu unit (Note, the exhaust is all the same size) but the price difference...

Re: Why does the Milwaukee M12 extended reach 1/4" ratchet cost $10 more than the 3/8 Not sure that the M12 fuel Ratchet is going to do these (brakes, bell housing, control arms) - they now make a M12 fuel right angle impact though, rated at 200+ ft lb.

Cold climate heat pump will work fine if you want A/C also, there is no reason I can think of to get 2 separate units. The Fujitsu for your size building will be a 9 , 12 or 15RLS3H. Probably a 9 would be MORE than enough. The cost difference of the different units is actually not big. I...

We just had our first couple of 0 F nights since I installed my Panasonic bath fan. My fan running at 80 CFM was just about right in my 28x28x10. 50 CFM had a tiny bit of condensation and 80 CFM basically had none. I can probably get away with just leaving it at 50 to save a little energy...

do you have a link to the product?

In a tightly built garage I need continuous ventilation and I didn't want to do an air to air heat exchanger in a garage. The air is very stale if there is no air movement and window condensation will occur at lowish temps. I don't need the same rate all the time. It is dependent on the...

I went ahead with the 50/80/100 Panasonic fan. I put it on a short 3" duct. I realize it is a bath fan and is fairly small, but the plan is to run it continuously. I'll report back when we have a single digit night to see if there's any condensation on the windows in the morning. Generally...

I am looking into using a Panasonic bath fan for my 28x28x10 spray foamed 50F garage in VT. Burner is direct vent, negative pressure not a concern. This is only $85 but has an oval duct. It is a DC motor...

I use a tiny 1/4 hex impact adapter and it does Lug nuts on normal vehicles just fine. It's 2553. I don't know if you are working ona big truck , then you probably need a m18 3/4 anyway. I could see the benefit of something as small as possible but has more torque than the 2553.

I swear I saw M12 ratchet with battery and charger for $99 in the most recent Northern Tool catalog which got recycled - has anyone seen this deal - or was it just the ratchet + battery without charger (which is also available right now for $99 from HD)? I have this tool and love it (along...

What is the best (easiest) floor for a DIY, new concrete but I don't really want to get into grinding the floor so can I use a gel acid etch? I've been reading around and polyurea seems to be a good bet. Are your poly urea kits from legacy industrial?

Any thoughts on this product for the garage floor...

Ohhh... thats a good question, I have no idea also considering the garage doors take up a huge portion of the north face of the gable wall so there's even less wall on that side.

I didn't design it (the builder did) but I am not quite sure what you mean. Meaning that the trusses are putting all of the weight on the outside walls which are just regular old 2x6 walls?

I wonder if the garage does not house any vehicles, gasoline, paint, oil, flammables, etc. Do I still need drywall separating the garage and apartment? It is a significant expense and I'm trying to figure out if I can still rent it out from time to time without it.

Did all of the apartment electrical myself - no pics, too busy working! Spray foam is going in now. Garage walls, ceiling, apartment walls and ceiling. So they can be kept and heated at different temps.

Hi - I don't think I said so. It is about 30 ft and 7 inches from the slab to the roof peak. Pretty big, but the max building height allowed is 35' here.

Here is 1 more with the barn lights - we are down in the Sugarbush area.

Just waiting on last light fixtures