Search results

Thanks, but the toilet is now installed:thumbup: and its gets a bit cold here, snow ect so -uhhhhhh yea, i need a bathroom. but its also a laundry room and the full utility room, well presure tank, water heater ect. RUMBLON

ten minutes away from me are heavy pines. forest. i just have no desire in live in the heavy trees and deal with pine cones and more bears. RUMBLON

I can build, so Im going to have to build my home as well. I have a set of barn home plans that approx 2000 sq ft. It can be made bigger as that sq footage does not include the shed sides that we will use for a surround porch. Im not sure if im going to build this or something similar to the...

Cambridge is like 360 or so in town, more outside of town. Its a ranching area. As far as trees, we have some down in the small gorge area that the water runs down during most of the year. No river, run off and springs. Its all intermediate wheat grass here, cow country, rolling hills and...

Here are a few pics as requested. The shed side is only 30x16. The shop runs 40x30. I would have gone the whole length but all my serer lines leave out of the other ten feet. This building was started 6 years or so ago before the real estate bust. I have three pieces of land on thsi 175 acres...

I have enclosed my new shop, an approx 1700 sq ft shop In Idaho. Much smaller than the 4200 sq ft I had in Nevada but its all mine and will work for me. That said It has a small bathroom in it that I am configuring and building now. It will be complete with toilet, sink, shower and a washer and...

Its going be be a nice shop, good luck with it. RUMBLON

Looks like a lot of good old barn wood too. Out west they sell that to folks for good $. We need more pics, whats the size and I guess your climate is moderate, no snow or snything? RUMBLON

very nice shop!!!!!! RUMBLON

draglink, I like it, but just finished this up to this point. Its getting racedeck next summer.

Well, since I have been out of the picture for a while, long back at work and doing fine. I just built or started to build me a little bar/ cigar/ sinatra corner in the front shop that will be show only. I still have plans for the racedeck but new appliances changed it for a while. I did build...

none out there?

Well, its been four years, still using it? Rumblon

Well after a long time away from the project, its time to ge back on it. Sooo many projects and too much time at work on overtime hours. Think I am going towards this kind of look? what ya think? RUMBLON

I am trying to get inspired and get back on my shop/ garage cigar bar area in my 3600 sq ft shop. I have been so busy doing other things that I have left it for a year and now its time to get back on it. Im trying to decide what to do for the wall areas inside the bar area and thought I would...

Well you were correct, it was made by Kennedy. However Kennedy could not help at all and said your "S.O.L. Cornwell said the same. So any suggestions on just finding some look alike piece of trim/ drawer pull that I can fabricate and cut, build to fit to make it look close? Any suggestions? Dave

I have a 40s mopar grille, but its sticks out wayyyy to far. I kind of thought of that, either a grille or something but most stick out even a little which does not allow the person sitting at the bar to sit up close if need be.

Ok, I thought I would check here and see if I can get some creative advise? I am in the middle of building a MOPAR hotrod bar for the MOPAR shop. I have decided that the front of the shop an approx 900 sq ft is going to be where I hang out and smoke a few cigars, talk shop, have a weekend scotch...

airbuff101, ITS THE BLACK TRIM/ HANDLE THAT GOES ON THE TOP EDGE OF THE BOTTOM DRAWER IN THIS PIC HERE. It measured 38 3/4 long

airbuff101 :bowdown: Thanks a ton, I am in need of this part here, thats missing from the top of the large bottom drawer? Any # in that catalog for that? I will do some searching for Kennedy tool boxes. Thanks again RUMBLON