Search results

If you do get the portable AC, turn the ceiling fans OFF. With 16' walls you can keep the lower 8' cooler with the heat rising and not stirring into the lower area. Direct the flow of the AC straight across at 4' high.

Looks like supply and return are 14" dia on the side and condenser air inlet on the opposite side with outlet on top. Not meant to be used indoors, just park it outside with duct running to the building like any package unit. 5 tons will help, but with 16' walls, open ceiling, no insulation and...

Howdy neighbor!

:rocker: What he said.

https://www.homedepot.com/p/ATMOR-13-000-Watts-240V-2-25GPM-Electric-Tankless-Water-Heater-Includes-Pressure-Relief-Device-Ideal-for-a-Full-Bathroom-AT-WH-13HD/312683084 This is what my shop has. Full bathroom plus utility sink. Well water is usually 50 - 60 degrees and no problems taking a hot...

PVC strapped to a 4x4 would work temporarily. I would advise installing a pressure regulator too.

$9.97 on the shelf. Ordered online for pickup. 4 packs @$5.97 Cool beans

The Inficon Dtek I used for many years finally bit the dust. Replaced it with the Inficon Ultrasonic and it works well for refrigerant leaks and a few other things. Biggest problem I have is windy locations (same for heated diode) and electronic noise. Just about blew out my eardrums with the...

The only way to know if the condenser coil is clean....is when you clean it. You'd be amazed at the dirt I've washed out of what LOOKS like a clean condenser. Is the small copper line (high side) hotter than the ambient temp? Can you check your ductwork for obvious leaks? Is it in the attic? The...

+1 WARRANTY ECM motors will rock back and forth to determine rotation before starting. No external capacitor. I've replaced some walk-in cooler and freezer ECM evaporator motors that would run for a while, then slow to stop, then rock back and forth and spin again for a while.

Call me a curmudgeon. Someone is almost always at my house, so, non-programmable tstat. Set it and forget it. Fewer bells and whistles to break. How much energy are you saving when your HVAC system has to cool the house down after being off all day?

I use them on most every service call for hex head screws. Not very useful for nuts except to start them. Most of the time the stud bottoms out . https://www.malcoproducts.com/categories/magnetic-hex-drivers/ These are fantastic.

A pdf of the owners manual is available. Google the model number mfg1f3030t3nov Page 22 shows the procedure to replace the thermocouple. www.uscraftmaster.com › pdf › manuals › BFGmanual

post the brand and model number. maybe someone can find a parts diagram. sometimes the pilot burner, thermopile assembly has to be replaced.

+1 Unistrut Easy peasy. A 10' stick would be plenty to make two pieces.

My plumber friend uses tape and thread sealant together. No leaks. "I scramble out to run to the other side of the garage and turn the breaker off." You need a power disconnect at the pressure switch.

5gl buckets and some u shaped pieces of rebar makes some anchors/weights that are easy to move with a small tractor.

Does your condensing unit have a low pressure switch to prevent the compressor from running if the refrigerant has leaked out? Yes = replace evaporator coil. No = replace everything. A flat system will pull in air/moisture if the compressor continues to run. POE oil is hygroscopic. Even changing...

Gypsum will help the clay, but it takes some time and or tilling.

Will this extension fit your model? https://www.husqvarna.com/us/accessories/attachments-combi/extension-attachment/967297101/ The Milwaukee trimmer, pole saw kit I got for my FIL has an extension, but I've only tried it on the pole saw attachment. For the trimmer I'd think it would put the...