Search results

Sadly you are correct after I looked the 12” freeflow is 1/2” thick where as the 18” xlc you have is 3/4” thick. One thing I might suggest - playing off the (2 floor idea). Layout and construct the materials you already have for each garage bay and later join the two garage floor areas with...

Do the entry of the garage in 12” for a row or 2 then lay the 18 for the rest of the garage. Granted the seams will line up every 3rd tile at the garage entry. 3-12”=36 2-18”=36 I don’t think it will look bad at all. Justify it in your mind as the 12” tiles are your border. And the 18’s are...

Shop looks great. I’m biased since I have a flush mount scissor and can say you’re going to like using it to work on your projects. This weekends project for me is building a wheeled worktop to span my platforms.

This phase is finished ! Kept left side with full pieces and the remaining 4” to the middle. After watching where the normal car that parks here stops, this side should allow for 24” AccuPark spot if desired. RaceDeck - do you make the the Accupark in your other color offerings...

Seems contrary to people’s taste. But if you go mosaic on the floor. Do a darker grout. Or do a complimentary, yet darker tile all together. The floor doesn’t have to match the walls. Most just don’t want to mix another batch of grout. Sent from my iPhone using The Garage Journal mobile app

Jack. When searching for a jackshaft opener I went through the same thoughts you did as far as features. “Why can’t they be simple” I ended up buying the 8500W but have not and don’t plan to hook it to my homes WiFi server. The 8500w is really nice unit as it contains the backup battery...

All done.

More progress on the lift. All anchors drilled and torqued, everything is level. Had to shim the driver side a bit. And within 1/8” spacing between lifts. Engine end something like 41 1/4” space Rear spacing 41 1/8” Separated the halves on my own carefully checking to make sure I didn’t get...

Just bolted down the scissor lift. Today. Should be operational tomorrow.

A 2x4 will get you 1 1/2” inches away from your wall then add a 1x4 you should be good out past your pipe. Find your studs Space some 3” screws to the edges of the 2x4 and save the Newage supplied lag bolts for the center after drilling a small diameter pilot hole. Here’s what I did in...

Nicely done. Looks great Sent from my iPhone using The Garage Journal mobile app

Finish the rest tomorrow

Little work this weekend

I’d suggest anyone covering a flush mount scissor lift use the largest one piece cover. My thinking is if you use the stall/garage spot year round the mat needs to lay under the perimeter of the vehicle your driving not just the scissor lift itself, otherwise water,snow, salt just Falls of...

Hope the OP got the piece cut. May I suggest a contour tool to “measure the piece” and transfer it to the Racedeck piece. Just Incase you need to remove the piece to actually cut it. Just about any Dremel bit will cut plastic. Even the sanding disks. Just run it SLOW. Speed/heat created by the...

Plan made. I’ve got kids in college so this is going to be done in 1/3rd’s middle around the lift being first. Went ahead and decided on all 12” tiles Diamond Tuffshield, Snap Carpet and Non gloss diamond under the tool boxes/cabinets. No one can see it and it’s 1.00 cheaper. Green (wood...

Hose reel and air for safety locks are set.

Re: RACEDECK[emoji2400] Holiday Deals Tuffshield can be placed on circletrac? [emoji848]

Here looks to be the plan for now, with some snapcarpet infront of tool boxes. There will be some cuts but it should leave majority of the small pieces inside the lifts footprint and a seam just to the outside of the daily drivers tire path

I took the air chisel to the pits and leveled out the scissor lift.