Search results

Reed 2C Vise -- local pickup only. No shipping. Previously cleaned up and painted. Split washer has been welded -- I guess somebody thought they would "fix" it not knowing it was not broken. Slide sadly abused but not cracked as image shows. Otherwise, decent shape. Also selling a Reed 3C, 3...

Local SF Bay Area pick up only. See link below for images. https://www.garagejournal.com/forum/threads/the-vintage-toolboxes-of-garage-journal.49743/page-254#post-7580969

No saw. I have no idea if it's complete. Minor rust. The saw guides and miter move freely. I thought is was a Langdon but was corrected in the Millers Falls thread. I prefer to trade for Craftsman long C combination wrenches. I already have 1/2, 5/8 and 11/16. Also looking for a Circle U and BE...

This 4" Wilton 400 is usable in its repaired state. It's otherwise in decent shape; the jaws are quite nice. It's on a DIY swivel base. I prefer a local pickup. If shipped, you pay whatever it costs me via UPS (I can't fit it in a USPS flat rate box).

Left one, small diagonal cutter, Snap On Middle one only has a diamond symbol-type marking. I have no idea of the manufacturer but I'm including as it has vacuum grips. Right is Forged Steel. $40 shipped

I'm hoping to trade this vise for Craftsman Long C combination wrenches (I have 1/2, 5/8 and 11/16) and/or 3/8" drive Circle U sockets. It's in decent shape with some abuse on the dynamic jaw (I didn't do it). The pipe jaws appear to be a bonus as I do not see them in search result images.

Starrett items: No. 436 1-2" Micrometer (owner's marks) No. 185 Drill & Wire Gauge Both $45 shipped

I have this to trade. I'm looking for Craftsman combination wrenches. I am looking for these without owner's marks: Long C: * 3/8 and smaller * 7/16 * 3/4 and larger =V= series: 1/4" 5/16" 1" Here's what I have. Misc. Durochrome, some Chromium Vanadium and D-I sockets; overview of Indestro...

I picked up this 3/4 HP Dayton repulsion start motor from a free pile. It runs but a little noisy -- wouldn't describe it as a hum. I don't know sugar from shinola about electric motors so excuse my ignorance. I managed to remove the keyed pulleys from the shaft and !thought! I could then remove...

Sold Miscellaneous Snap-on stuff. $75 shipped. Detail images on request. * 1/4" sockets are 6 and 8 point -- TM 6, 7, 8, 9, TM 408 E and TM 410 E * Drill index is numbered 1 - 60. * Four 1/2" sockets and swivel * Two 3/8" sockets and ratchet

Want to trade for any Long C Craftsman combination wrenches and specific =V= series combination wrenches. No owner's marks please =V= series: 1/4" 5/16" 1" Have these Proto screwdrivers, ratchet/sockets, pipe wrench and ball pein hammer to trade. Details on request.

I would like to trade this for Craftsman Long C combo wrenches (I'm searching for many sizes). Also looking for Craftsman =V= series combos, 1/4, 5/16 and 11/32. No owners marks, please. Appears to operate as intended and looks to be complete but I'm not knowledgeable so caveat emptor. Can't...

Selling as a set. Each wrench is in a different state regarding wear, grime and rust. Please look carefully. I do not see any obvious owner's marks but in other pieces, I've been surprised after cleanup. $60 including shipping. I've checked for typos but please check images. And the date...

Partial Set No. 1411 8 point: 1/4, 5/16, 3/8 6 point: 1/4, 9/32, 5/16, 11/32, 3/8, 7/16 77MC Ratchet 18M Flex Box: some rust outside; clean inside $35 including shipping I'll include 3/8" drive 6 pt. metric sockets: 9, 10 and 11mm I'm also going to sell other ratchet sets such as 1/2"...

Anybody make use of these? Ampco screwdriver is about 10" and smaller screwdriver is not labeled (I'm pretty sure it is BeCu but not 100% certain). $30 shipped.

I refurbished this and cast a collar in bronze. It's just been sitting (as I have an everyday Athol beater and other cherished Reeds) so there is now a bit of rust on the handle and jaws. The side images show the homemade collar it came with. A nice bonus with this one is the wrench. It's a...

I acquired an old Hyro Metal Punch having never used one, old or new. I assumed (wrongly) I could figure out how to use it. I can insert the punch with the right die (I think that's the right terminology) but after punching a hole, the punch stays stuck in the sheet metal when I lift the...

I have a 12" disc sander powered by a Rockwell 220 3 phase motor (1 hp, 3.8 amps). I've wired it through a VFD for single phase; it's been fine up until recently. Now, I have to spin the disc in order to get it going. I've done some research (I am not an electrician) and kinda sorta...

Sold S-K Roll Pin Punches 6151 1/16" 6154 1/8" 6155 5/32" 6156 3/16" 6157 7/32" 6160 5/16" $25 shipped. Sold!

I rescued this swivel base from a busted import vise in the dumpster. Perhaps someone can use this. The outside diameter is 5 1/2" with the two clamps about 3/4-7/8" in from the edge. Shipping plus the price of a six pack for my "handling" which should total less than $20 (won't fit in a...