Search results

I just started my quincy 210 up for the first time in a few years and it wont build pressure. It ran fine for manynyears but has sat for awhile now. It doesnt make any hissing or leaking noise. Just runs like the unloaders arent working. Anyone more familiar with these that could tell me what...

Craftsman tool/ toolbox lot - quincy compressor Looking to sell this lot of craftsman sockets, ratchets, wrenches. Everything in the pictures is included. I'll pack It up in the craftsman toolbox and send it for actual shipping. Random assortment. Mostly craftsman v or vv sockets and wrenches...

Vintage Black & Decker 1/2" "Junior" Drill, Works, Needs a new cord, $20 Plus Shipping Skil Home Shop 1/4" Drill, Works, Needs new cord - $10 Plus Shipping Metabo BE 751, Made in Germany, 0-1000, 0-3000 Drill, 6.5 Amp, With Case - $125 Plus Shipping Skil Saw Circular Saw, Made in USA, 10 Amp...

Kennedy Machinist Toolbox Style 630 3 Drawer - $50 Plus shipping Dorman Organizer (Fuel Fittings) - $20 Plus Shipping PM or Email - [email protected]

Sears Metric Hex Drive Socket Set - $20 plus shipping In good condition, Does not look to be missing any pieces. Item # 946273 Plomb 1220 5/8" Wrench - $8 Plus Shipping Plomb WF-15 7/16" 12 Point Socket - $2 Plus Shipping PM or Email- [email protected]

With all the new developments and costco selling the mr cool mini split i think I have made my mind up on getting one of those for my attached garage. I could use some insight on if 12k or 18k is the right size though? The attached is 23x25 with a vaulted ceiling going from 8ft to 16ft at the...

Does this pump appear to be a legit saylor beall 703/705? Thinking of looking at it this weekend. Also can anyone tell me what to look for to id it?

Is there a certain type of wire brush wheel for a bench grinder that does not expand out so much that it chews up the grinder? I just installed a Weiler 7" X 3/4 brush on my 7" block grinder and with the guards on the grinder the wires chew up the side plates. I'm just wondering if there is a...

Enter to win a bash hammer or wilton vise. wilton giveaway

So I'm wanting to run a 120v 12/2 wire about 80ft from my shop to my back gate. I'm looking for input on what is required from a code standpoint. I'm thinking 12/2 direct burial but what is required as far as the trench? What depth ect? Where in the nec covers this sort of thing? I read...

Just thought I would post up what I just got done fixing. Had the exterior ac unit stop this afternoon. Found one of the #8 feeder wires burned through. The red wirenut was melted and some of the wire missing. One question is a red wirenut correct for a #8 to #10 wire? I put larger blue wire...

Can anyone look at my panel and tell me if it is installed correctly? Apparently it is a three phase panel as every third lug has no voltage. I'm concerned about the grounding as the way it appears now the ground wire is handling all of the loaf for the neutral. I need to do some more checking...

So I have two westinghouse industrial ceiling fans that I just recently installed. Link shown below. FAN LINK Last night I finished up wiring the controllers. Link to controller below. Westinghouse controller So the problem is when I turn on the switch the fans only move very slow. And...

I've currently got wires run for two ceiling fans in in my shop. I have it run back to a single box for one switch to control both. I'm looking to use the industrial type fans that I have read about here on gj. Question is can two ceiling fans be wired to a single fan controller? Ideally I'd...

Doall 16" Bandsaw Rebuild I'm starting this thread to document the rebuild of my 16" Doall vertical bandsaw. Im hoping to get some feedback and advice as this is my first machine rebuild. I have read through all of APMech's thread several time and already used it to help with dissassembly of...

I started to clean up my Grandpa's Old Columbian 605 vise a about a month ago and just put it back together tonight. I am still not done completely but it will work with the soft jaws i have in it now. This is the only real before pic that i have of it. What I wanted to do was to remove the...

I thought this was interesting when i found it surfing the bay...

Well, i have been lurking here for a while and thought i would finally introduce myself and show you my dirty shop. For a little background about this place. This house and shop was built by my grandparents in about 1993. The lot is located on a cul-de-sac so the lot is one of the largest...

okay quick question. If i am going to get a roll of bandsaw material and only want to spend the dough for a blade of a certain tpi. is it better to get a higher tpi and have to wait longer for it to cut thicker stock or get the lesser tpi? I do occasionally cut 1-1.5 bar stock and also smaller...