Search results

I need to make this hex shaft air hammer bit fit in to a round shaft air hammer. The smallest diameter of the hex is the same diameter of the of the round. Also, the round part of the hex is too large. Yes, I know a lathe would be perfect for this but I don't have one and don't know anyone with...

I am want to purchase a 3/8 stubby pneumatic impact. Was looking at the m7 and found a few different models. Can anyone tell me the differences? I have even called them and the customer service did not know the difference. The models are Nc3612q Nc3611q Nc3610q Which models are the oldest to...

Anyone here own one? Looking for some feedback. Want to purchase the xb452 just for basic tpms and bead surface repair. I really like the the compact size but how well does it work especially with beads stuck to the rims? What has me concerned is the ram travel is just under 1.5". Is that...

Anyone here looking to sell a used pico 2204a? Maybe someone here has upgraded? Would be willing to sell it to someone who is learning how to use a scope? Thank you Sal

Compressor hs781002aj Pump hs750000p I have been trying to find the owners manual for this husky compressor without any luck. Would anyone have it or maybe a manual for just the pump? Manufacturerd in 2004-2005. Thank you.

Currently, when my impact aircat 1155 runs there is a 20psi drop at the gauge on the regulator. I have an 80 gallon 2 stage compressor with a old craftsman (16008) line filter going in to a (16022) regulator/filter. The 3/4 out of the tank is reduced to 3/8 which is the size of the regulator...

This question might be obvious for some. Most people use quick disconnects for their air tools. I placed milton v style at the tool end of the air hose. If I place the same fitting at the compressor end to be able to remove the hose would that reduce the capability of air flow. I know the...

Looking at a used air hammer aircat 5200at. What are your thoughts? Wanted a 118max but found this. Has anyone compared these two? Think one is better than the other? https://aircat.com/composite-long-stroke-air-hammer-442

The bushing where the valve seals against is all dried up, so there is air leaking past all the time. The part number on sears website says it is obsolete.Part number 40 #8700880. Think I can get this seal/bushing from somewhere else. Can it be that specific to that wrench? Can easily replace...

What size cutting tip would you have in the torch for an automotive shop? Heating and cutting stubborn bolts and nuts. Exhaust, flanges and anything else that gets in the way. Was looking at a Smith's website and found their charts for oxy/propane tips. Which tip would you have in your torch...

About to make the move and order a Rotary ATO7. Does anyone here know the best place to order it from?

I have been trying to install a lift in my two car garage for a while now. After a lot of thinking it over, here is where I stand. I am limited to 127'' width and I have a 11' ceiling but have a beam which runs parallel to the overhead switch which limits the cars max height to 10'. So, a...

Was sold on the idea of a Atlas Apex 10. Went down to the nearest Greg Smiths to check it out. Really loved many of the features of this lift. Double s shaped columns made it compact and sturdy, came with screw in adapters and truck extensions, single point lock release, 2 and 3 stage arms and...

Had this automobile jack for some years now. The other day as I was rolling it the caster fell apart. Went on the internet to find a replacement - discontinued. This was an expensive jack and I don't want to see it go because of this reason. I have access to a mig welder but need an idea how to...

Does anyone here have this lift? Looking for a lift for a residential garage so it will not be used to often. Need to safely lift a 6000 lb vehicle. Greg Smith is close so there will be a reduction from the internet price since there will be no shipping charges. I know it is not a Rotary or...

In the market for a two post lift for hobby use in my home garage. Must be made well enough to lift a Suburban down to a Saturn and work under it safely. Certification is a MUST! Have been looking at 10,000 lbs overhead units. These are the companies which I have bookmarked. Challenger Rotary...

I am new to this site and registered because of the knowledge about the Chase Parker 974 Vise. If, someone could please help answer my question it is much appreciated. My father gave me this vise and I noticed something odd about it. If you look at the picture you will see a washer behind the...