Search results

Bridgeport No 30 Hacksaw. Really dont know anything about it and have too many saws! $30 shipping included. Paypal, Venmo, Check accepted

Hope this is ok to post here, not having luck on CL. 1965 BSA Lightning 650. Has had head bored / new cylinders. I did new clutch plates, coils, cables, and carbs. Also has new mufflers, and any chrome was re-chromed. Has been sitting a few years but was running when stored. Stored in...

Not for the garage but on my house. The house was built in the 70's and uses 12" Masonite / hardboard / smooth lap siding. Dimensions are 5/16" x 12" x usually 16' long. We're doing some renovations and I'll need a few pieces for that. I sourced some before from a local lumber yard that randomly...

Two cans of Clausing oil. Hydraulic oil is almost gone, probably less than 1/4 can left. Way oil is probably about 2/3 to 3/4 full. $20 + shipping OBO

South Bend Lathe Face Plate 7 1/4" diameter, 1 1/2" - 8 TPI. For 9" south bend lathes. Has minor wear and a couple cut marks as seen in the photos. $65 + Shipping South Bend Lathe Drive Plate, for driving lathe dogs when turning between centers. 6" diameter. 1 1/2" - 8 TPI for 9" South Bend...

Well no wonder my router wouldn't raise and lower! The gear has broken. I've poked around for a couple days on marketplace and Craigslist, but I have not found a donor. Would anyone happen to have a donor router for sale, or possibly just this gear? It's listed as part #27 in the manual, and...

Stopped by the American Precision Museum yesterday, located in Windsor, VT. About a two hour drive from where we live, so an excellent day trip. For those who do not know, the museum started life as an armory producing rifles in the 1800's, and eventually moving to consumer products. I've...

So I'm restoring an old shopsmith, and the threaded one of these "nuts" is stripped. I'm going to make a new one myself, but I was actually just more curious what it was actually called, and if they were commercially available? Im leaning towards it being called a clevis, but I've found no...

We just remodeled our kitchen, tore down the old sunroom that was attached to the kitchen, and framed that area out to add to the kitchen sq footage. The sunroom was on a concrete pad, and we had to put joists on top and fill the spaces with rigid insulation, so no plumbing is in there, or can...

Nice old Sioux valve seat grinder. In Ok condition cosmetically, but still works well, pictures show all the wear. Has lots of pilots and wheels, and two jigs (Not sure if that's what they're called) that go with it. Comes in the carrying case. Prefer local pickup in central MA, but if you want...

I got this in a bunch of stuff from my cousins who were cleaning out there father's tools. I could never figure out what it was. It almost appears to be a one off, or perhaps a peice of in house shop made equipment. That whole side of the family is from Westboro / Shrewsbury area of...

Hi everyone, So I'm making a new vise nut for a customer's Prentiss vise and I need some confirmation on one aspect of it. It's seen some abuse, and I want to make sure it was manufactured a certain way vs. it wore out this way. You'll see from the photos that he dovetail is tapered along the...

Normally I'm ok with typical household electric stuff, but when it comes to motors and especially drum switches, I just seem to be in the dark. Also, I've never dealt with three phase power before. I have a three phase motor for a Bridgeport shaper head. I have a VFD to run it off of. As far as...

So I looked a little and couldn't find a thread or much info on this. I Know sandblasting sheet metal can warp it, but I've also heard if done right it won't warp. I have an old grey / red Craftsman tool box and rolling base I'm restoring, and I would like to have the main bodies of both...

Two (one of the three in the pictures is gone) 8" diameter slitting saws - appear to be unused, all three are 1/8" thick, staggered teeth. Both also have 1 1/4" bores, only one is marked Niagra. $15 each or $25 for both + shipping 1" boring bar set, cemented carbide. one bar has the carbide...

1/4" letter set - missing X. $10 1/8"number set complete $10 Both for $15, prices don't include shipping. Both sets are 'reversed' They read normally on the stamp so when you stamp into material they are backwards. Sent from my Pixel 2 using Tapatalk

I have my shop in the basement of my house. I have one side the machine shop - bridgeport, lathe, bandsaw, etc... and the other half has the woodshop. My workbench runs about half the length of the shop, also helping divide the two shops. It has a 'wall' down the middle up to the ceiling. One...

Long story short - we tore down a sunroom attached to our kitchen to add onto the kitchen, the sunroom had a foundation but they poured a slab on top and there was never access to underneath because the sunroom foundation was added on after the house was built (not that it matters since there...

I have 8 repro Craftsman chevron badges for tool boxes i just made up. They are aluminum and hand painted then clear coated for protection. They do not have the clips like the plastic ones, so they must be affixed with epoxy or double sided tape. The bottom one in the picture with three is an...

Selling this Union tool box I got from my uncle's tools that I have no use for. In great shape for it's age, some minor scratches and rust top is just dusty. $20 + shipping. Sent from my Pixel 2 using Tapatalk