Search results

I bought this knife at the GEC store in Titusville in 2024. It is marked "S" for store or second. It is in new condition. I have not carried, used, or sharpened the knife. The pull is fairly strong on both blades. Not a nail breaker, but pretty firm. They both have a firm half stop...

Looks like it was barely used, if at all. Just a few very minor blemishes. 19 3/4 x 7 x 8 $69 plus shipping Paypal, check, or money order

I picked up this little anvil at an estate sale recently. It only weighs 21 lb. No markings on it that I can see. I was hoping it wasn't imported junk. Everything at the sale was old and quality tools and machines, so I took a chance on the little anvil. I realize it's too small to do...

I bought this yesterday at an estate sale. I actually thought it was a vacuum pump, until I got home and looked it over. It runs okay and puts out air, but I've never seen a compressor without a tank. How is it used? Connect it to a separate tank? Or just fill your tires slowly? It's got...

#14 Head locking handle. $15 #15 Table locking handle. $15 #16 Tapered table indexing pin. $15 #17 Spindle locking handle. $15 #18 Head casting. Pick up in Dayton, OH. No shipping. $20 SOLD #19 Base and column. 2 1/4" OD. Base is badly rusted. Column is not too bad. Should clean...

#1 Table. Casting no. 22213-103. One small divot marked with yellow pencil. $30 #2 Table mount. $15 SOLD #3 Motor. 1/2 hp, 1750, 1/2" shafts, reversable. Runs well but bearings sound a bit noisy. Nice badge, no dents in sheet metal center piece. Good switch. Cord is rough. Dated 1955...

Unfortunately, PC has discontinued all their routers. I think this one predates the 7518 router. It's a beast. Weighs 17.5 lb. No plastic. Built for heavy production use. It came from a home shop. The previous owner shortened the cord for use in a router table and installed a crappy plug. You...

These lamps are all identical. The previous owner had them mounted on all his machines. They are made by National Morelight Co, in Buffalo, NY. The goosenecks are sturdy; they will stay put. The shades are plastic and they thread on to the lamp socket. They mount onto a bracket with a 3/8"...

Includes the often missing jaws on the top. Top is 7x7, base is 8x8. Top rotates 360* It needs a good cleaning and lubrication. Everything turns and operates as it should, but it's pretty stiff. I wire wheeled the top surface and it cleaned up nicely. It is all complete and nothing is broken...

These parts are from a 397.195891 grinder, but will fit other similar 6" block grinders also. 1. eye shield $20 2. eye shield $20 3. Left tool rest $20 4. Right tool rest $20 5. Wheel cover, fits both sides $20 6. Wheel cover, fits both sides $20 7. Wheel guard, fits both sides $20 8. Wheel...

It fits either side on a 6" grinder and includes the three screws. $20 plus shipping. Paypal, check or money order. Send a PM with your zip, and I'll get you a total.

A nice older made in USA machine. The serial number dates it to 1973. 2 hp single phase motor, runs on 115v or 230v. Currently wired for 230. The saw came from a home garage workshop, so I don't think it saw a lot of heavy use. It runs nicely, very smooth. The fence allows a 49" cut to the...

1/8", 3/8", 5/8" 3/4", and 1" They're in decent shape, just need sharpened. $43 plus shipping. Send me a message with your zip, and I'll look up the shipping cost. Check or money order. Sorry, no electronic payments.

#1 Lighted eye shield. No damage and it works fine. 115 volts. $40 plus shipping from 45342. #2 Right side wheel guard. No damage. Includes mounting flange and screws. $25 #3 Left side wheel guard. The slot for the tool rest is broken off. $10 #4 two spark arresters. $15 Prices do...

These are both made by Dazor. They are fully adjustable at the joints and they swivel and rotate. #1 is an incandescent lamp. It works fine. The base is held down with two screws. The cord looks like it was shortened or repaired, but it works fine. $45 plus shipping. #2 has two...

These parts fit 6" Craftsman "block" grinders. The mounting screws are included. Prices do not include shipping. Send me a PM with your zip what parts you want and I'll look up the shipping cost. I accept a check or money order. Sorry, no electronic payments. 1. Left tool rest. $20 2...

Craftsman gooseneck lamp. Takes a bulb with small threads as shown. The round shade is pot metal and the mounting clamp is plastic. Switch and cord are good. It works fine. Asking $25 plus shipping. Check, or money order accepted. Sorry, I don't take any electronic payments. Send me a pm with...

I have two of these grinders for sale. Had to split into two listing because of the limit on the number of pictures. These are the older cast iron block grinders, much heavier than the newer aluminum ones. Approximately 40 lb. each. They are complete. These earlier ones did not have wheel covers...

I have two of these grinders for sale. Had to split into two listing because of the limit on the number of pictures. These are the older cast iron block grinders, much heavier than the newer aluminum ones. Approximately 40 lb. each. They are complete. These earlier ones did not have wheel...