Search results

Background: i had previously glued down 1/2" cork to concrete basement floor. We had put some rugs down but never did anything with it otherwise. Fast forward several years, we are now inclined to put down flooring, ideally LVP. I thought we had a pretty flat resulting floor, until we went to...

This will be for the basement, poured concrete. Years ago, in an effort to insulate the cold floor so the kids could have a designated play area, I glued down sheets of 1/2" cork then we just put some rugs over that to protect it. Now we are looking to put an actual finished floor in there, over...

I'm building a sound-dampening box for my air compressor. I want to have a setup where the drain valve on the tank stays open, having pipe exit the enclosure with a shut-off valve outside of the box. What type of hose / pipe / fittings do I search for to use for this?

Collection of vintage Craftsman router bits and some extras. Most are unused (or at least look that way to my untrained eye) Asking $65 shipped to your door. Right-hand row, from top going down: Craftsman USA 9-21262 Craftsman USA 5/32 25587 Craftsman USA 15/16 25581 Craftsman USA 1/8...

Model 2276-20 Includes tool, detachable probe, 12v battery, charger, hard case, instructions I bought this new, used it <10 times. It's in practically new condition. Asking $160 shipped to your door. West coast, texas, florida add $10 more to cover shipping.

Collection of Fine Homebuilding and Family Handyman $10 for each stack, shipped to your door. $15 for both.

My daughter alerted me that the (electric) dryer wasnt working right. I went to investigate, got a faint smell of electrical. I took the outlet out and found one of the hot lines melted into the outlet. See the pictures. It has been hooked up for 4+ years without issue. Thoughts on what would...

For a limited time, save $15 on all Pocket-Hole Jigs over $99 purchased online, at a home center or your local retailer details here...

I have a metal custom-sized chimney cap - basically they took a sheet of metal, layed it over the entire top of the chimney, broke it over each edge, then cut a hole in it for the covered vent to sit in. The metal has started to rust as it appears that there's no slope to it, and water will pool...

I recently built an outdoor firepit out of concrete pavers. Now I'm at the point of adhering the firebrock to the pavers. The dude at menards said to use refractory cement. I mixed a small batch and put 5 firebricks in place as a test run. I stacked some bags of mulch up against them to hold...

My house has the older-style oak boards, 2 1/2in wide. These were installed with 1/16" gap in between each board. Maybe that was the look 20 years ago, but I tire of dirt and debris settling in these cracks. Along with this, of course I have some scratches and marks. I got a quote to sand and...

I want to use something like this to put on the wall, pull down, put shoes on it intermittently. It looks like the hinge has a horizontal piece that limits the movement of the wood piece anything past 90°. Is there a particular name for this type of hinge so that I can locate it?

Not sure what these go to. No name / markings on these at all. Some previous rust, pitting is present. I honestly have no idea what they are worth. If $30 shipped isn't a fair price, shoot me an offer.

I'm assuming these are for a cutter or scraper of some kind but I can't seem to find this exact one. If anyone has a name for these that would be awesome. Thanks in advance

Both of these are missing the clock mechanism. Surface is in pretty good condition. Each has some damage to one of the bottom corners, as pictured. Asking $75 each or both for $130 - shipping included.

Project for this winter is to tear up and redo one of our bathrooms, including a 6' x 3' door-less walk-in shower. Anyhow, we managed to get the porcelain tile in the link below at a decent price as lowes was doing their inventory clearance. I've not done tile work previously, but I would...

Willing to negotiate and make deals on anything listed, if you don't like my prices. Questions or need more info / pictures. Dont hesitate to ask. Bear with me as there's a lot listed here, but I can just about assure you that if you see it still it, I still have it available for sale...

Can anyone ID these? I have a couple guesses, but I don't want to influence your thoughts. Hammer thingy has Taiwan on the rubber handle, but no other markings. Metal press thing - no markings - threaded bolt threads easily

Most, if not all of the other forums i've been to have an option to go to the 'first unread' message of a thread, usually when viewing from the subscribed-threads page. Best option that seems to be here is the last page. Any chance that could become an option?

I'm doing some craft-like projects with some old, cheapy wrenches. I don't want the chrome look on them. I've had some luck with heating them, letting them cool, then running them on the wire wheel. Any easier / better way to do this?