Search results

I bought these two CRAFTSMAN tool chests quite a few years ago. The bottom cabinet has the two middle drawers that appear to have dropped out of the drawer glider channel (see photos below). Is this common for CRAFTSMAN cabinets? Is it due to putting too many tools in the drawers. Any comments...

PPG primer, PPG catalyst and Feather Fill G2 for sale 2 gallons PPG primer, 2 bottles of PPG catalyst and 1 quart of Feather Fill G2 for sale! $125.00 picked up in Dayton, Ohio. I WILL NOT SHIP THESE ITEMS! USPS Money Order is the only accepted form of payment pre-paid. Ask any questions you...

Spray Guns and other accessories for sale AEROPRO HVLP GUN SOLD PENDING FUNDS to member JDMopar! AEROPRO HVLP Spray Gun G6600-13 with 1.3 tip. I bought this a number of years ago from TCP Global. It had never been used until this year when I sprayed a test panel with it in Viking Blue lacquer...

LOPI Wood Burning Stove fireplace insert. I believe this is the largest insert they sold that year. $600.00 with pick-up only in Dayton, Ohio. This baby weighs around 600 lbs.! I WILL NOT SHIP! Payment in cash (prefer 100 dollar bills) or USPS Money Order only! No electronic payment will be...

Has anyone plumbed one of these into their air lines to condense any water in the air? Should I worry about any contaminants in the cooler and if so, how should I clean it internally or will the inline filters remove contaminants from the air? I'm going to use this moisture separator/regulator...

I'm working on shut offs for bathroom sink and toilet supply lines. Years ago, I sweated on the cheap shutoffs and they are old and are hard to open close. I've decided to add ball valves to the supply lines where they come out of the wall. I'll have to heat up and remove the old fittings and...

I'm sanding down the OAI (Ram Air) hood on my 72 Cutlass 442. I'm sanding the old paint off and plan on repainting the hood as well as the rest of the car with Duracryl Viking Blue metallic lacquer paint and clear coating it with their High Performance clear. I will be using KONDAR red Oxide...

I have an ATLAS PV10PX and am happy with it so far. I was wondering the other day what you would do if you happened to have a vehicle up on the lift and set on the upper safety stops and a seal blew out and you loose hydraulic pressure? How would you get the vehicle down. If I were waiting on...

I have finished walls inside with the slick side of the OSB inward. Is it recommended to paint OSB? If not, that's OK......I just thought about painting it in the future. I sure don't want to create an issue with peeling of the paint.

I am planning on installing 3/4 inch Rapid air maxline air lines in my garage shortly. I am hoping that those of you who have installed the same lines can post some photos of your installation where you straightened the tubing without using the expensive Rapid air maxline straightening tool! I'd...

Does anyone know where I could find an unopened NOS gallon KONDAR (DZ7) red oxide primer? I really like the stuff and my paint store says it's obsolete! I guess it's just like me....LOL! Thanks for any info, OLE442

Anyone on the forum ever drill a well with an auger? This would be just for emergency use and maybe watering the garden. Thanks

I tried to search with no results.....I'm search challenged, I guess! I had my 24 X 30 garage built 2 years ago but decided to insulate and sheetrock it myself. It is 2x4 walls with 9 foot tall walls and 2/3 of it has sizzor trusses with approx. 12 foot peaks. The walls were Tyvek wrapped over...

My 24 X 30 garage needs insulation and sheetrock installed and I have questions. I have wood frame with 7/16 OSB Tyvek wrap on the outside with vinyl siding over that. Should I just put fiberglass insulation with the kraft paper towards the inside before putting up the sheetrock? Would that be...

I have gone round and round with the lift thing and am ALMOST settled on a Challenger CLFP9 2 post lift. Just curious if anyone has experience or good info about this choice since I really want to get one before I'm too old to use it. I have 12 ft 2 1/4 in peaks on the sizzor trusses my ceiling...

Good afternoon! I'm just curious if an members have experience with Automotive Equipment Warehouse, Inc.? They are located in Plain City, Ohio. I'm looking to buy a Challenger 2 post lift and possibly to have it installed and was hoping to get some reviews on other members experience. Thanks...

Looking to buy either a 4 post or 2 post lift in the near future for my 24 X 30 garage. I have moved back and forth on whether to get a two post or four post? I want one to be able to work on brakes, do oil changes and maybe exhausts. I’ve also thought of storage however have room for all 5...