Search results

Looking for a flashlight. Specifications 1. about 4 inches long 2. uses 3 AAA batteries in a cylinder holder 3. Has a lanyard. 4. Brightest possible I know that other specs would be better but I really need one this size. Don't want rechargeable batteries for this one. Any suggestions?

Needing a 24 X 30 inch workbench 36 inches high. Looking at building something like the image below. However, it needs to be 36" tall without wheels. The bench legs should sit on the ground with some way to put wheels down in order to move it. I know they make Retractable Casters but these...

I have the meter surge suppressor supplied by my electric utility. I also have the Siemens FS140 on the breaker panel and the Intermatic Compressor Defender on the HVAC condensing unit. I'd like to add a surge protector on the air handler with heat strip which means it is 240v. The air...

This was factory installed. I can't see any type of thread locker on it. I tried holding the brass part with a pipe wrench and using a wrench to tighten to make it parallel with the side of the reel. I also tried to unscrew it. Both without success. I do not have any way to heat the joint...

I'd like to find a storage reel for 100 ft of 0.75 OD pressure washer hose. Really would just like a reel with a stand without any pressure washer connections. I use the 100 footer a couple times a year. A 50 ft is used most of the time. Something that looks like this would be great...

I've been using these for years and have never run into the issue that arose today. I have one on a 13 HP Honda. Been on that engine for several years (OK, 14). It still shows #'s so the battery isn't dead. I always buy direct as they recommend. Anyway, today the tack registered 1 hour use...

Does anyone use the 3/8" Flexilla 50' hose ? This has the 3/8 inch connectors and isn't the small 1/4" hose with M22 connectors. I can't find a you tube review of this one - only the 1/4" version. My current hose works but it is stiff, hard to coil up and when stretched out, it wants to...

I've been using the cheap plastic ones but they soon lose the ability to lock the blade either open or closed and thus are difficult and unsafe to use. Usually throw them away long before I use all of the blades. Looking for a better made one. Prefer the 18mm blade. What would you suggest?

I saw a mechanic use what I think was a snap on extension. It was about 6 inches long and had a blue sleeve over it so that you could use the sleeve as a hand hold. What are these called?

My landscape lights have a connector that has pins that penetrate the wiring sheath. There isn't any waterproofing ability of the connector. They are slowing corroding and failing. What is the best way to connect 3 wires and have them be waterproof? I know they make wire nuts with silicone...

I have a section of aluminum fence where the bracket holding it to the post came loose. I took the fence section out and the screw (should have been 2) evidently chewed out the threads in the post and backed itself out. May have been stripped when the fence was installed. It was a small 1/2...

The air handler is in an unconditioned closet in the garage. The closet is generally cooler than the garage and still is. However, we are getting condensation on the air handler cabinet. Unit is an up flow Carrier. When I noticed the condesation, there was enough to wet the top of the box it...

I have a 10020 air compressor. I accidentally turned it over and damaged one of the intake filter housings. I had a spare one so that is now OK. However, there is a part on the tank below that intake that is labeled VOR 110v AC 4.5VA 4.1ma 100% ED IP65 that now begins to bleed air when the...

I have the air compressor and it has always been a pain for me to move it around. It is about 36" tall. The handle makes it hard to balance the unit and roll it around as I have to be in sort of a crouched position to reach the handle especially after tipping the unit to get it onto it's feet...

I am wanting to bore a hole through a piece of pipe and have it exactly centered. Not necessarily exact but very close. I have a flag pole that I want to bore a hole through 2 sections at a time so that I can use a Clevis pin or a PTO pin to lock the sections. I've found a jig (The Drill Rite...

I was using a non impact rated socket adapter on my Bosch impact and the adapter broke with the "connection" end still in the quick change bit holder. Any way to get this out? I assume it has twisted slightly and has thus locked itself inside. When I push the end of the quick change like you...

I have 1 2Ah battery and 3 4Ah batteries. Only have 1 each of the chargers. Can a 4Ah battery be charged correctly with the 2Ah battery charger?

Seller wants $45. It's on Craigslist. Here are his comments: "5" SWIVIL REGULAR STRIGHT JAWS AND A LOWER SET OF PIPE JAWS, 13" CLOSED" Any idea about the maker and whether it's worth $45?

Just as the title says. Just got this installed and need assistance on which hooks, etc to purchase. Not sure if HandiWall has unique accessories or not. Anyone know? How about a link or 2 to sites that have accessories at a reasonable price? I'm wanting to hang about 4 fishing rods, a...

Well, during transport of my toolbox, it fell in the truck. Several drawers opened but one drawer caught on something and it bent. Now the drawer will not close. I tried to straighten it without any success. Any idea how to get it working again? How about how to take it out? Are...