Search results

IT HAS BEEN SOLD This 1962 Craftsman 150 Bench Top Drill Press was my father's, and was purchased on 10/24/1962, as indicated by the included original receipt. I'm also including the original operating instructions / parts list, and the 1954 revised addition of Catalog No. 2921: "The Drill...

Circa 1940 - 1950 Craftsman / Crafty Rotary Tool "Case Only" With Some Accessories SOLD It belonged to my father, who purchased the Rotary Tool Kit at some point between 1940 and 1950. This case was introduced by Craftsman in 1940. After 1950 Craftsman no longer used the underlined Craftsman...

SOLD It's a spare that I rescued from my parents old electrical service when they updated their service. It's basically new... As they never owned an electric range, therefore it's never had a fuse in it.. These are hard to come by, & having a spare can mean the difference between a simple fix...

SOLD I have one Murray "Range", & one Murray "Main Lighting", 60 amp pullout fuse block. Both fuse blocks are from my parents old electrical service. The range fuse block has never had a fuse in it, as they never owned an electric range. The main lighting fuse block includes the two working 60...

I found these lying on the side of the road. Considering where they were found, & even though someone tried to use the back side of the jaws as a hammer, they're still in perfect working condition. The jaw teeth themselves are in good condition showing only minor wear to a couple of the teeth...

SOLD Unlike vinyl windows you can pick up at Home Depot or Lowes, these both have fully welded construction rather than being mechanically assembled with screws. One measures 20 1/4" x 28 1/4" tip to tip, & the other one measures, 20" x 30" tip to tip. Both windows have 1/2 screens, & the longer...

SOLD While digging deeper into my fathers workshop I found another heavy steel plate. This plate is just over 12" square, is 5/8" thick, & weighs 23 lbs . Unlike the 2 previous ground steel plates I listed, this plate is not ground, & has been rough cut on 2 sides. I can say with 100% certainty...

SOLD They would make great speakers for use in a work shop, or a man cave. One is stamped, 328604 (left one in photos), & the other one is stamped, 328607 (right one in photos). The number 328 is the EIA (Electronic Industries Association) code for Utah speakers. The 6 represents the last number...

BOTH PLATES ARE SOLD While going through my father's workshop, I came across these 2 heavy steel plates that I remember from his gunsmithing days back in the mid 60's to early 70's. The first one measures, .615"(5/8" Nominal) x 7 9/16" x 8", & weighs 11 pounds. As neither one has been touched in...

SOLD Although used, it's in perfect working order. Its only wear are some scuff marks on the reel itself. There are no manufacturers identifying marks on the reel, but I do know that it's of better than average quality, as it was originally installed as part of a Picker portable X-ray machine...

Found them hanging in my father's workshop. Although each one is slightly different, they both measure 3 5/8"/3" diameter x 1" high x 1 1/4" hole. One is light brown & the other is light gray. The labels on each have a numbers stamped on them.The brown wheel can be easily read: RA60JV21C. The...

SOLD It measures 10" in diameter by 5/32 thick. The center hole measures 3/4", & there are total of 6, 5/16" holes around it. Three different holes are countersunk on each side. The wheel is without damage. It weighs approximately 3 1/2 pounds, & packaged weighs just over 4 pound, giving it a 5...

SOLD This 1725 rpm motor was used to power a combination belt/disc sander that I recently sold her on GJ. It's in perfect working condition, & is very quiet when it runs. I'm asking $50 OBO, plus the cost of shipping. It has a 20 pound shipping weight, & will be shipped UPS Ground from Zip...

SOLD It was purchased by my father, circa 1972, & has been sitting idle for the last 4 or 5years. The sander uses standard 4" x 36" sanding belts, & 6" cloth or paper back sanding discs. The platen table/work rest, shown on the belt sander has never been used & was attached for show in one of...

SOLD PENDING PAYMENT I came across this vintage Craftsman 2" square that was my fathers. I found it tucked away on a shelf in what was his workshop. The part number is MY40401, & the box indicates it was made in England. Although I can't say for certain, I believe it dates back prior to 1972...

I'm the original owner of this one piece insulated coveralls / overalls hunting suit that dates back to the 70's. It's the perfect outerwear for stand hunting during extreme weather conditions. It also makes a great snowmobile or work suit. The suit is rated to -50°F. What's nice is not needing...

SOLD This antique wood tool chest belonged to my father, & was made for him by his grandfather, circa 1927-1931. His grandfather worked as a carpenter for the Erie RR in Port Jervis, NY. Overall it measures 31 1/2" long, 13 1/2" wide, & 10 1/12" high. The top was made from a single board, & has...

I have the following small lot of mixed sockets for sale. They're mostly Craftsman, with a Proto, & Williams piece thrown in. There are no markings on any of them. I'm asking $19.00 for the lot shipped. That's less than $2.00 a socket, plus $5.15 for Priority mail shipping. If interested please...

SOLD My father was the original owner of this bullet trap / target trap / target backstop. It is what I shot into when I was learning to shoot back in the mid 60's, & used until the early 80's when we stopped shooting in our basement. It hasn't been used in the last 30 plus years. The face of...

Vintage Skil Model 1616 2.2 CID 16" Chainsaw W/ Original Parts & Users Guide SOLD I am the original owner of this, 1976, fully functional chainsaw. Both the automatic & manual oiling systems are functional as well. I'm asking $65 OBO for it, plus the cost of shipping. It will be shipped by...