Search results

Funny timing I replaced the clips for the second time on my charger yesterday. When I replaced them the first time I bought some cheapos from Amazon and they were so thin you could bend the ears that were to crimp the wire by hand. That lasted about a month. I got some Muellers (the one right...

At your price point I would also jump on the Keen Bandwagon. My criticism of Keen is that they seem to come unglued for me around year #2 weather or not I've used them much. Keen has a wide toe box by default, for me that is a big deal. Many other brands even in a wide are too narrow at the...

The Milwaukee trigger issue is well known and common. I had the same on my 1/2 impact and my circular saw. In both cases the tool was new enough to be under warranty. In the case of the Impact wrench the one they sent me back was refurbished and was clearly not as new as the one I sent in. I...

The smaller Hex impact driver will do you fine from what you describe. It will probably even exceed your expectations on what it can do. Follow Mikey's advice and get the new one, you'll be happy with it. I have a half inch impact wrench and a hex driver and almost never use or need the half...

I've had a ton of decent deals over the years none as good as some that are posted here. More frequently than a good deal I see the tool I'm looking for at near full new price, sometime higher than new price. That I don't understand. I mean it happens a LOT I half wonder if it's a money...

I've been tracking Milwaukee batteries for a while now, because a man always needs more of them. I ulled the trigger on this today, IMHO this is a legit good deal...

This is likely the last siding project I will involve myself in. If I were to do more I would consider the shears.

For sure on the respiration filter, I overkill any time I create dust nowadays, 3m half face with particulate and organic filters stacked. I find that the 3m is only slightly less of a pain than a "covid" n95 mask.

A few follow ups, The tool is battery powered and about 4 years old. I hear you on the dust being a problem, but still, cement fiber board is one of the things that need cutting with a circular saw.

Folks, I have posted and read many posts regarding Milwaukee's trigger challenges. This weekend I was cutting cement fiberboard siding and had a scary problem. The trigger on my Milwaukee Circular saw was sticking in the "on" position after I release d the trigger. As I was using a cement...

I use silicone caulk as adhesive sometimes. Works pretty well for a removable adhesive

Sold! I only wish I needed another saw...

for $29 more I'd get the similar Ridgid. Or for $39 more I'd get the Ridgid 5hp.

Blade is a Diablo 14" metal blade. It has a Max RPM of 1800.

Hey guys, follow up here. So first off I did this and it worked. Let me address some of the points made. First off I should have provided more detail in the beginning. I don't pretend that this is a great GJ level solution. I have a 20+ year old makita miter saw that I got for $10 at a garage...

I often buy a tool for a specific need then end up using it a ton, then look back on how I ever survived without it. To call out one, I'd have to say my Kubota Tractor with Front end loader is my best tool buy ever. I know that expands what the OP probably intended as a "tool" but I use that...

Folks, I have read many threads here regarding ac motor speed controllers and I think the answer to my question is a flat no but figure I'll ask. I have an old non-brushless Makita miter saw that I want to use to cut metal. I need to slow the saw in order to be in the safety zone for the metal...

Another option may be to buy a full set of spares wheels. Then you can always have one set to be at the man.

The M18 Fuel

To the OP, I have had a ton of work done to my homes in the past 10 years including a major remodel and having a new home one built from scratch. Here in Central and eastern NC all the framing pros that I've watched use Dewalt or Milwaukee cordless. I'm that guy who stops and asks a pro how he...