Search results

From the looks of that drawer I have to ask, "do you just collect tool or do you also use them?"

A few electrical suggestions. In my new 25x25 I used three of LED tri lights above the work area and another three near the rear (front/rear separately switched) . I also installed three outlets on the ceiling for drop down corded worklight and for me 240v for my lift on either side ( so I can...

In clearing out my workshop, today I was planning to list this week on Facebook Marketplance my Silverline British Standard Whitworth Combination Wrenches (8 pieces) and two sets of sockets reqular and deep.

I agree that the degree of tilt will not be used, but I still want to restore fully. Any idea where to locate the degree scale?

We're talking about tack welding on the ramps not the lift itself. A tack weld on the side of the ramp is not going to compromise the load factor for the ramp. There are many videos of tack welding under the ramp to either secure a spring loaded setup or locking device.

My closest "car guy" friend passed away and his wife asked me if there was a tool of his I wanted. When we worked in his garage I recall him using his Wilton Multi-use vise the most. So to remember him, I am in the process of a restoration, The degree scale was totally erased. I have searched...

I use tape to mark the max height. However, since I use the lift for three different cars I have three tape lines marked with the various vehicle types. When I had a 10 ft ceiling I installed a spring loaded arm on the ceiling that when triggered would set off a small buzzer. I set this at 5...

When I priced the Milwaukee M12 Expander I contacted six tool rental places and none of them rent one. I only need to use it for 7 connections in my garage. I can do with the $20 crimper I used on one sink line. Too bad since there are these nice chrome covers for the Pex than only work with the...

Aslo swapped out the two fixed casters for HF swivel casters. Bolt patterns the same. Added bumpers to the front legs so it doesn't hit my cars

I use a Lodesol magnetic mat for the inside lid to hold my tools when I am on a project. I have also added the magnetic US General towel holder on the side and a US general 25lb hook on the back for a 25 ft. extension cord. BTW, there are some very good videos on guys who have modified the 5...

I didn't catch that about Simple Green not good for aluminum parts. My HVAC guys only recommend Simple Green on cleaning the aluminum louvers on my external A/C components. I've used it for years and no issues. So what is the problem with Simple Green?

sparky 1971. Unfortunately, all their additional code requirements are in writing with the latest edition of NEC codes. When I first started the wiring, I forgot to review the amendments, but my electrician who wired the 150 amp service to the main panel told me about it. One item that was not...

Sparky 1971. Because I live in one of the most over-regulated counties (often called the Republic of) in the US. As well, my garage required AFCI's as they don't distinguish garages from other structures. Don't even ask me the headaches I had with our water authority on their code requirements...

In building my new garage, our code required not only do I have to have a refrigerator on a dedicated 20 amp line but it must also be GFCI protected.

What size is your garage? Wasn't aware that this is not a single person operation. I spoke to Armorpoxy and yes they have excellent customer service, but no mention of recruiting help to apply.

I am just finishing up my dream garage build and have been so busy that I have not had a chance to chronicle on GJ. Definitely a Bathroom. I added a full bathroom/shower in a room above the garage with a kitchen area and fridge. In the garage area, you should have a sink for washing car...

I just went through the whole process you are contemplating (will chronicle the process in GJ in a week or so). You didn't mention how large a parcel of land you intend to purchase. If small you will need to determine if it is a buildable lot (contrary to other comments, it doesn't usually...

I have had the same problem. The magnetic base which holds the battery compartment will latch onto metal and slightly loosen causing a bad connection. So try to make sure its tight. Also, if the battery is low it will go on for a few seconds or so and then switch off. You think you have a bad...

Don't have time for the install as I need to finish up rough in plumbing, some framing for the mini-split head unit and insulation. Trying to wrap this up by year's end. The plumbing, framing, insulation are not a problem, so something has to be farmed out.

Thanks for the confirmation on the Hyper-heat. A second HVAC company is recommending a Daikin unit never mentioned Hyper-heat. Just waiting for his estimate. On HVACdirect.com the Carrier unit sells for 4k, but their bid including labor was over 12k. and this is a straight forward job as I...