Search results

Those Wheels are updated. Same as the ones i have on my 2021. **** yours have the lighter shade of grey "Spokes" instead of "Charcoal". looks like the headlights have been replaced as well. i dont see any fogging of the plastic. I had to get another Tundra since the 2012 had completely died...

i do have the insulated panels installed on the exterior of the metal roll up door. i also have a heavy Freight Elevator padded "Curtain" hanging on the interior in front of the door with a small dead air space. During winter, i always keep my driveway cleared

i have looked at other doors. during the build phase , the other garage door footprint consumed the overhead and interfered with the Heater; about a foot away from the door roll space. i didnt even think a door like this would be uninsulated for this region. i have even considered the flexible...

that is exactly what i was referring. thank you. and it is my plan to have this as a Drawbridge. hinged at the bottom and raise it up to protect the existing metal door. I currently have 2" foam boards installed in front of the metal roll-up door for Winter time with a man door for entry. my...

its been Decades since i learned Mechanical Drawing. **** i would like to know what scale to use to make a Drawing and figure out a bill of materials. the existing garage door is a metal roll-up and during Cold HArd New england winters i can open the garage to deal with removing large items as i...

it was supplied with the building I bought.

Excellent! i believe a few 1x3's to make a frame and a few gussets to keep it true. Many Thanks!

it would only be opened when required to get the snow removal gear out. i do have some elevator blankets. they are to be hung inside in front of the roll up door.

that small roll area at the top is one of the reason i posted. i tried the reflective foil **** the clearance when rolled up is a thin piece of felt is one of the issues i noticed. and the Down position gives a huge gap.

wondering if you gurus have come up with a solution to install some type of insulation to ward off New England Cold weather. i can only think of some sort of insulated panels for winter use that allow me to remove quickly if i have to move something in/out and wont fit thru th eman door.

no sir! compression fittings have a required method to tightening to the required spec.typically below 1/4" nut to hand tight then 3/4 turn. that is to prevent "Necking the Joint" i.e. too much tightness will compress the ferrule into the tubing and can flare the End that is inserted to cause...

TRUE DAT! **** Brainwashed Garage Rats wont ever learn until their Mentors confirm the mistakes they espoused years back.

TRUE DAT! **** Brainwashed Garage Rats wont ever learn until their Mentors confirm the mistakes they espoused years back.

thanks, i should have mentioned i bought the original craftsmen set about 35 years ago. they have been of good quality so far. i also have About three sets of Greenfield T&D sets as well from same era

many years back i purchased the original 39 piece Tap n Die set Part number 52382. i decided its time to but the upgrade kit, 52384. and as described on the sears web site: Description Item # 00952384000P Model # 52384 Larger size taps and dies to upgrade 39-pc. set. **Includes case to also...

thats an alternative. **** truth be told i looked around last night for some you tube vids and even saw one from Eastwood that shows the install as you had it. many others have other setups that contradict the Eastwood setup. regardless, some things i have come to know from working in...

okay, i have learned something new again! you installed the Vac Suction in place of the Air inlet to the Cabinet after removing the diversion port? as opposed to the "Filtered" Vac Port? i have assembled these small bench-top units a time or two and cant recall any of the various distributors...

thank you Gentlemen

Any of you fine Snap-On Garage Masters happen to have any Documentation for this Model? WB250 Wheel Balancer. There was some discussion many years back **** nothing for this Model noticed during my searching. Regards Dave