Search results

got it. put it in the freezer overnight and heated the body up. I couldn't get anything behind it to pull up the low side without leveraging off the body. There really wasn't any easy way to grab and extract it either. The only way I could think to get it free without damaging an important...

I was thinking maybe something to pull up the low side after the heating/cooling, rather than hit the high side down??

Sorry about that. I attached a part break down and circled the part that is stuck in the gun. Its the end plate that holds the bearing that is stuck halfway down to where it is supposed to sit at the bottom of the gun. I made an approximate little red mark on the body in the photo. The spot it's...

Not entirely sure how I managed this. This is an IR 231A. I tore it apart to clean, lube and replace all the gaskets. I've got the gasket kit, so I started reassembly. I warmed the body up with propane torch similar to the way I did when removing the piece . It didn't drop all the way in, so I...

Just in case anyone is wondering, you can use a 3/4 length for both! Original jaw screws are Filister head 1/4-20 5/8 and horse shoe screws are small pan head 10-32 5/8. Thanks for the thread! Just found one to fix up. Wire wheeled it, cleaned up some of the casting marks, coated in BLO and...

It was a hidden screw that was on there pretty tight, so I assumed it was pressed on. Soak it in some penetrating oil if you're having trouble unscrewing it. Once you get it off, you'll have to replace the cork in the check valve and make sure the spring has enough tension. Stretch the spring...

made some more progress... unscrewed the wick tube with a pipe wrench. I would definitely recommend heating it or using a penetrating lube, as I slightly dented the tube when removing it. Then pulled the screen out and cleaned it. Any idea what the 2 small screws are for? I can seem to find any...

this site was also a pretty great source of info. http://blotorches.com/#theory

morph0711 I believe that would be the wick. I attached a pic of where mine is attached. you should be able to unscrew the long wick tube and you might be able to replace it after you do that. I suppose you could drill it out as well. I would assume if you want the blow torch to run continuously...

Hey guys just picked up a blow torch and im trying to get it running. Would love to take apart the check valve and replace the seal, but I cant figure out if there is an easy way to remove it. I attached a picture. I cleaned everything else and the only other thing id want to replace is the...

Jason...thanks for the run down!! Ill try adjusting for a bit and use some blue painters tape on the threads to get it even with the arbor. The made in the usa ones I found were on ebay. They seem really well made, so im determined to get them balanced Will a little bit of vibration cause wear...

Lol zoomieport...let me know if you need to free up some space over there! Id definitely be willing to buy one of your smaller wiltons that needs some work!! Thanks guys!

Got a couple better pics. I have a wheel similar to the one notlob posted. Although it doesn't sit on the threads, it still doesn't run smoothly. The washers fit quite well and I tried to square it up before putting it back on, but it still isnt perfectly centered. I might try the card stock...

So i ended up just cleaning it up, putting some johnsons wax on it, and a thin layer of grease on the screw. The angle grinder with the cupped wire wheel helped with the residual black, but the black coloration came back after I put wax on it. Thanks for the help guys! :thumbup:

So Ive taken apart, cleaned up and upgraded this old craftsman block grinder that I got a while back. I wanted a fine wire wheel on one side and the grinding wheel on the other side. After lots of searching, I found a solution for a fine wire wheel that didnt have the little 5/8 to 1/2 arbor...

Where would i get original colored paint?? Most of the paint on the vise is in great shape. There are a few bare spots and those large spots on the neck in my last pic. Would it be possible to strip those rough areas and do more of a touch-up or would the paints not match that well??

Short update...I went at it with an orbital sander and wire brush instead, since the sandblasting shop was closed today. Attached a few pics of the progress. I cant seem to do anything about the slight black discoloration (pitting?) where the rust used to be on the slide. Ill wax it when Im done...

I was thinking of taking a wire wheel or a stripping disc to it, but I'm worried about the area where the screw travels. I cant get any tools in there to strip the rust. That's why I was considering sandblasting. If I didn't sandblast it (or could have someone just sandblast the rusty areas), i...

did the sandblasting remove the rust leaving a nice finish to paint/wax and did you have issues with rust after? Your vise looks great! That should be the original yost blue. No idea what paint to grab that would be close to that color though

I picked up a yost vise a while ago and havent gotten around to fixing it up yet. Aside from the obvious rust in the pic, there is a bit of rust where the screw passes through. The white is just a little wax (tried to keep it from getting any worse). Im deciding between having the whole thing...